How to run a 3D print farm: setup, safety, quality control and capacity
A working guide for print shops: fire and electrical safety, ventilation, standard profiles, the job workflow, quality control, capacity math, maintenance, pricing structure and routed jobs.
By Printlooper Team · Published · 24 min read
Key takeaways
- Plan the room around fire and electrical safety first: an electrician sizes the circuits, every printer sits on a non-flammable surface, smoke alarms cover the room and firmware thermal runaway protection stays on.
- NIOSH reports that printers can release ultrafine particles and VOCs. Give printers their own room, enclose and filter or exhaust them, and keep resin work separate.
- Standardize printers, nozzles and locked slicer profiles per material, so any operator gets the same part from any machine.
- Inspect the first part of every job against the spec before printing the rest, sample the batch on a written rule and log every defect with its cause.
- Plan capacity on hours you can really use, minus changeovers, maintenance and failed prints, then set a daily order cap below that number.
- On Printlooper routed jobs, decline with a reason when you cannot do the work, delete files after shipment or link expiry, and never subcontract a routed job without written consent.
One printer is a machine with a queue. Ten or fifty printers are a production line, and the hard problems change: fire safety, electrical load, air quality, consistent output, honest capacity and getting the right part to the right address on time.
This guide is for print shops running or growing a farm, whether you sell your own products, take contract jobs or fulfill marketplace orders. Safety comes first on purpose, followed by fleet setup, materials, workflow, quality control, a worked capacity example, maintenance, pricing and routed jobs on Printlooper.
Every number here is a starting point, and every hazard instruction defers to your printer maker, your materials' safety data sheets and your local fire and electrical codes.
Pick the work your farm is built for
The kind of work you take shapes everything else: which printers you buy, how much material you stock, how you price and how much admin you carry. Most farms start with one of three models and add a second later.
| Model | Where orders come from | What you control | What it demands |
|---|---|---|---|
| Your own products | Your own shop, storefront or wholesale buyers | Designs, prices, branding and batch sizes | Marketing, product rights and product safety, plus stock planning |
| Contract and on-demand jobs | Businesses and individuals who send files for quotes | Which jobs you accept and how you quote them | Fast, accurate quotes, file checks and clear terms on tolerances and finish |
| Marketplace routed jobs | A platform's sellers and buyers, with orders sent to your shop | Materials, colors, pricing settings, capacity and which jobs you accept | Consistent quality, on-time shipment, file handling rules and a steady acceptance record |
Your own products give you the most control and the most responsibility, including the product rights and safety rules covered in selling 3D prints legally. Contract work rewards shops that quote fast and hit tolerances. Routed work trades some control for orders that come through a platform rather than your own marketing, and rewards reliability above everything.
Space, power and fire safety
Heated beds and hot ends run for hours, and a heater fault is a fire risk. Prusa explains that if a thermistor comes loose, the heater can reach dangerously high temperatures while the printer reads a falsely low one, which is the failure thermal runaway protection exists to catch. Plan the room so that one failure stays one failure.
The room
- Put printers on metal racks or other non-flammable shelving, with non-flammable surfaces under and around each machine.
- Keep cardboard, paper towels, isopropyl alcohol and other flammables out of the printer area. Store solvents closed, in a separate cabinet, as their SDS directs.
- Leave clear space around vents and power supplies, keep clearance below any sprinkler heads, and keep walkways and exits clear.
- Keep the room dry and within the temperature range your printer maker lists.
- Keep children and pets out of the print room.
Electrical load
A farm puts many long-running loads on the same wiring. Before you fill a rack, find each printer's maximum rated power on its label or spec sheet, add dryers, lights and fans, and have a licensed electrician decide how many circuits you need and what each can carry. The US Fire Administration advises against overloading outlets and power strips, recommends strips with internal overload protection and says to replace worn or damaged extension cords right away. NIOSH's 3D printing guide says a ventilated printer rack should be designed around electrical supply limits and avoid power strips. Do not feed racks from extension cords: have your electrician add outlets where the racks need them.
Stagger start times after a power cut or a morning restart instead of starting a whole rack at once, and ask your electrician whether your circuits need any other limits.
Detection and extinguishers
Install smoke alarms that cover the print room, and choose interconnected alarms so that one sounding sets off the rest. The US Fire Administration advises testing alarms monthly and replacing them every 10 years. Keep a suitable extinguisher near the exit. OSHA classes fires in paper, cloth, wood, rubber and many plastics as class A, flammable liquids such as solvents as class B and energized electrical equipment as class C, and notes that multipurpose dry chemical extinguishers suit all three. A print room in a business space can also fall under local fire code, so ask your local fire department or fire marshal what applies, from alarms to extinguisher type and placement to solvent storage. If a fire is growing or you are unsure, get everyone out and call 911.
Firmware, monitoring and unattended printing
Thermal runaway protection cuts power to the heaters when temperature readings stop making sense. Keep it switched on, keep firmware current from the printer maker, and never install firmware with the protection disabled. Add cameras so you can see every printer, and a way to cut power remotely, such as smart plugs rated above each printer's maximum draw and certified by a nationally recognized testing laboratory (NRTL), or a shutoff your electrician installs.
Printers, especially those with heated beds, should not run unattended unless you have taken the fire precautions your printer maker recommends: at a minimum smoke detection, a non-flammable surface and firmware thermal protection switched on. Some makers go further. Prusa's help center, for example, says not to leave the printer unattended while it is switched on, and Purdue University's safety office tells its labs never to leave printers unattended during operation. Follow the strictest instruction that applies to each machine and write down your policy. Where a maker's instructions do not rule it out and you print outside staffed hours, have every precaution above in place and make sure someone can see the room and respond quickly.
Fire and electrical setup
- A licensed electrician has sized the circuits for the full fleet plus dryers, lights and fans.
- No overloaded power strips and no extension cords feeding racks.
- Every printer sits on a non-flammable surface, with flammables cleared away.
- Interconnected smoke alarms cover the room and are tested monthly.
- A suitable extinguisher hangs near the exit and staff know how to use it.
- Thermal runaway protection is on for every printer, on the maker's firmware.
- Cameras and remote power cutoff work from your phone.
- Your written policy on unattended printing follows each printer maker's precautions.
Ventilation, emissions and resin
Printing heats plastic, and heated plastic releases particles and gases. NIOSH, the federal agency that researches workplace health, says heated filaments can release ultrafine particles (smaller than 100 nanometers) and volatile organic compounds (VOCs), and that emission rates vary with the material, color, brand and nozzle temperature. Studies it cites found ABS produced higher ultrafine particle concentrations than PLA, and that resin printers released particles and organic vapors at levels similar to or above other printer types. A 2021 peer-reviewed study measured particles under 100 nanometers while printing PETG and recommended enclosing machines, local exhaust ventilation and combined gas and particle filtration.
A farm runs many printers for hours in one room, so plan controls for the whole fleet. NIOSH recommends the hierarchy of controls: substitute less hazardous materials and processes where you can, then use engineering controls such as ventilation and HEPA filters, then work practices and policies, with personal protective equipment last. Its practices include keeping printers in a separately ventilated room that people enter only when they need to, and watching printers by camera instead of standing next to them.
| Source | Main concern | Controls |
|---|---|---|
| Filament printing: PLA, PETG, TPU | Ultrafine particles and some VOCs | A print room separate from offices and living space, enclosures, local exhaust or HEPA filtration |
| Filament printing: ABS, ASA | Ultrafine particles and VOCs, with higher ultrafine particle concentrations than PLA in studies NIOSH cites | Enclosures with particle and activated carbon filtration or exhaust to outside, and fewer people in the room |
| Resin printing and washing | Skin contact with liquid resin, which can irritate or sensitize skin, plus particles and vapors | A separate ventilated room, nitrile or neoprene gloves, safety glasses, closed containers, and gloves and coats that stay in the work area |
| Isopropyl alcohol and other solvents | Flammable vapors, irritation | Small quantities, closed containers, away from heat, sparks and flame, stored as the SDS directs |
Enclosures and filtration
Enclosures keep emissions near the source and reduce warping on ABS and ASA. Pair them with filtration suited to what you are removing: NIOSH describes HEPA filtration for particles, with gas and vapor filters added when VOCs are a concern. For a bank of printers, its guide shows an enclosed rack with clear doors and a fan that exhausts outdoors. Check that filters seal and change them on the maker's schedule. Before you build a custom enclosure or exhaust, NIOSH advises having a qualified safety and health professional assess it, so it does not add fire risk, void the printer's safety certification or warranty, or create other hazards, and checking air pollution rules before you vent outdoors.
Resin
Resin printers need their own space and their own rules. Formlabs, a resin printer maker, tells users to wear nitrile or neoprene gloves to keep liquid resin off skin, wash exposed skin with soap and water, wear safety glasses during post-processing and keep solvent bottles closed because the vapors are flammable. Its resin disposal guide says not to pour liquid resin, or solvent containing dissolved resin, down drains: cure resin waste first and follow the SDS and local rules for used solvent. Treat these as a minimum and follow the instructions for your own resin and printer.
Standardize the fleet and slicer profiles
The cheapest quality improvement in a farm is sameness. The fewer printer models, nozzle sizes and profiles you run, the more predictable your output, spare parts and training.
| Standard | What to fix in writing | Why it matters |
|---|---|---|
| Printer models | One or two models on the same firmware version | Shared spare parts, one set of procedures, any job on any machine |
| Nozzles | One default size per material family, hardened nozzles for abrasive filaments | Profiles stay valid and wear is predictable |
| Slicer profiles | One locked profile per material and quality level, with a version name and change log | The same file prints the same way next month |
| Build surfaces | The same surface type per material, cleaned the same way | First layer adhesion stops being a variable |
| Calibration and labels | A logged calibration print per printer on a schedule, numbered printers, dated spool labels | You catch drift and can trace a defect to its source |
Treat profile changes like small engineering changes: test the new version on one printer, compare its parts with the old profile, then roll it out and note the date. For products you print repeatedly, save the plate layout, orientation and settings as a 3MF project file in your slicer, so a reprint is a reload rather than a rebuild.
Material storage, drying and inventory
Moisture is the quiet failure in a farm. Many filaments absorb water from the air, and wet filament tends to print with stringing, bubbles, rough surfaces and weaker parts. Prusa notes that nylon (polyamide), PVA and TPU need drying more often than popular filaments like PLA.
Keep new spools sealed until you need them, store open spools in sealed bins or dry boxes with desiccant and a humidity indicator, and feed nylon and TPU from a dry box during long prints.
| Material | Temperature | Time |
|---|---|---|
| PLA | 45 °C | 6 hours |
| PETG | 55 °C | 6 hours |
| TPU | 60 °C | 4 to 6 hours |
| ASA | 80 °C | 4 hours |
Use a filament dryer or a dedicated drying oven, never a kitchen oven used for food. Prusa notes that home ovens are imprecise and many cannot hold a temperature low enough without damaging filament, and that going over the recommended temperature softens filament so the windings stick together.
Inventory
- Set a reorder point for each material and color you sell, from your weekly use and your supplier's delivery time.
- Use first in, first out, so old stock does not sit open and absorb moisture.
- Record the material, color and lot on each job, so a bad batch can be traced.
- Count stock weekly. Weighing a partial spool and subtracting the empty spool weight gives a quick estimate.
Keep any marketplace material catalog matched to what you actually stock. On Printlooper, buyers who choose a material see only shops that stock it, so a stale catalog can send you jobs you cannot fill.
Job workflow from intake to shipped
A farm runs on one repeatable path for every job. Write it down, post it on the wall, and make every job carry a job sheet or ticket through it.
- Intake Log the file, quantity, material, color, finish, due date, shipping address, notes and hardware. Give the job an ID that follows the part to the box.
- File check Open the file in your slicer and check size against your beds, units, mesh errors, thin walls and support needs. Raise problems before you start, not after a failed plate.
- Plan and slice Load the locked profile, orient and plate the part, save the project, and record the printer, profile version and spool.
- First article Print one part or one plate and inspect it against the spec before you run the rest.
- Batch print Run the remaining quantity, checking each plate's first layer and watching the cameras through the run.
- Post-process Remove supports, clean, finish and fit any inserts or hardware the job calls for.
- Inspect and photograph Run your quality checks, photograph the finished parts to your photo standard and attach the photos to the job.
- Pack and ship Pack to protect the weakest feature, buy the label, ship and mark the job shipped so tracking can reach the buyer.
- Close out Delete customer files you are required to delete, file the job sheet and log any defects or remakes.
Packing and shipping
- Wrap thin features first, fill voids so parts cannot move, and double box fragile or heavy prints.
- Bag and label small parts and hardware together.
- Photograph the packed box before you seal it, in case of a damage claim.
- Weigh and measure the packed box before you buy the label, because carrier rates depend on both.
- Give buyers the shipping method and tracking, not delivery dates you do not control.
On Printlooper, labels for routed jobs are bought through Shippo inside the job flow, and tracking syncs back to the seller's Shopify store when it is connected.
Quality control: first article, sampling and defect logs
Quality control in a farm is about catching problems early and cheaply. A defect found on the first part costs one part. The same defect found by a buyer costs a remake, shipping and a review.
First-article inspection
Before you print a batch, inspect the first part against everything the job specifies: dimensions, fit, color, finish, visible surfaces and strength features such as clips. Measure critical dimensions with digital calipers, check holes with a pin gauge or the actual screw, and test-fit inserts and magnets. Sign it off on the job sheet, and repeat it whenever the printer, profile, material lot or color changes.
Sampling during a batch
You do not need to measure every part of a large run, but you do need a written rule before the run starts. A simple starting rule for a small farm: inspect the first part from each printer, every tenth part after that and the last part, and check every plate's first layer. When a sample fails, stop that printer and inspect everything it made since the last good sample. If a customer specifies a formal sampling standard, such as ANSI/ASQ Z1.4 for inspection by attributes, follow theirs.
| Defect | Likely causes | First fix to try |
|---|---|---|
| Warped corners or lifted edges | Poor bed adhesion, drafts, too much cooling for the material | Clean the plate, check bed temperature against the maker's range, enclose ABS and ASA |
| Stringing and blobs | Wet filament, temperature too high, retraction settings | Dry the spool, then tune temperature and retraction |
| Layer shifts | Loose belts, collisions, curled parts catching the nozzle | Check belt tension and pulleys, look for parts curling up |
| Gaps or thin walls | Partial clog, worn nozzle, tangled spool, wet filament | Check the spool path, clean or replace the nozzle |
| Dimensions out of tolerance | Profile drift, flow calibration, shrinkage | Recalibrate flow on that printer and compare to the locked profile |
| Weak layers or split clips | Printing too cold, too much cooling, wrong orientation | Check temperature and fan settings and the orientation on the job sheet |
Log every defect with the job ID, printer, profile version, spool and cause, and review the log weekly. Patterns tell you where to spend time: one printer with repeated layer shifts needs maintenance, and one material with repeated stringing needs better storage.
Photo standards
Photograph every finished order the same way: same background, light and angles, with the job ID in the frame or file name. Photos settle disputes and prove what shipped. For lighting and angles, see how to photograph 3D printed products.
Before a part ships
- First article signed off for this job, printer, profile and material lot.
- Critical dimensions measured and within the job's tolerance.
- Holes, inserts, magnets and hardware test-fitted.
- Color, finish and visible faces match the order.
- Supports, strings and sharp edges removed.
- Quantity counted against the job sheet.
- Photos taken and attached to the job.
- Any defects logged with a cause.
Capacity planning with a worked example
Capacity is not printers times 24 hours. Plates have to be cleared, printers need maintenance, prints fail, and a finished printer sits idle until someone starts the next plate. Plan on the hours you can really use, then set any order cap below that.
| Line | Hypothetical value | How it is worked out |
|---|---|---|
| Printers | 10 | Same model, same profiles |
| Staffed hours per day | 16 | Two shifts, so someone is present whenever printers run |
| Gross machine hours | 160 | 10 printers x 16 hours |
| Utilization after changeovers and maintenance | 75%, so 120 hours | Plates cleared, filament changes, scheduled maintenance |
| Failure buffer | 5%, so 114 good hours | 120 x 0.95, from your own failure log |
| Print time per part | 0.5 hours | A 2.5 hour plate holding 5 parts |
| Good parts per day | 228 | 114 good hours / 0.5 hours per part |
| Post-processing and packing | About 11.4 labor hours | 228 parts x 3 minutes each, so plan staff for it |
| Orders at full load | 114 | At an average of 2 parts per order |
| Planned daily order cap | 90 | About 80% of full load, leaving room for remakes, rush jobs and a printer down |
Run the same math with your own logs. The two numbers that move the answer most are utilization and failure rate, and both come from your records, not a spec sheet. Track them weekly.
Watch for the real bottleneck. Often it is people rather than printer hours: plate changes, post-processing, packing and customer messages. If staffing is the limit, more printers will not ship more orders.
A maintenance schedule that keeps printers running
Maintenance on a schedule costs less than repairs after a failure. Follow your printer maker's maintenance guide first, because lubricants, belt tension and replacement intervals differ by model. Switch off, unplug and cool a printer before you work on it: NIOSH notes that shock and mechanical injury are possible during maintenance if a printer is not de-energized. Use this table as a skeleton and fill in the maker's details.
| When | Tasks | Notes |
|---|---|---|
| Every plate | Clear the plate, check the first layer, look for blobs or strings on the nozzle | Seconds per plate, and it catches many failures early |
| Daily | Clean build plates as the maker directs, check filament paths and spool holders, review camera alerts and printer errors | Use the cleaner the plate maker specifies |
| Weekly | Check belt tension, inspect nozzles for wear, clean fans and filters, look over cables and connectors for wear or heat marks | Abrasive filaments wear nozzles faster |
| Monthly | Lubricate rods or rails per the maker, tighten frame fasteners, check heater and thermistor connections as the maker's guide describes, test firmware updates on one printer before the rest | Prusa links thermal runaway errors to thermistors and their wiring |
| Monthly, safety | Test smoke alarms, check extinguishers are in place and charged, test the remote power cutoff | The US Fire Administration advises monthly alarm tests |
| On wear | Replace nozzles, PTFE tubes, build surfaces, belts and fans | Log replacement dates by printer |
| After any repair | Run a calibration print and a first article before the printer takes jobs again | Record it in the maintenance log |
Keep a maintenance log per printer with the date, task, parts replaced and who did it, and stock the parts that wear: nozzles, heater and thermistor sets, PTFE tubes, belts, fans and build surfaces.
Pricing structure for print farm work
However you sell, a price has to cover material, machine time, labor, packaging, failures and overhead, plus margin. Building quotes from a few standard parts keeps pricing fast and consistent.
| Component | What it covers | How shops often set it |
|---|---|---|
| Per gram | Material, plus a share of machine time for typical parts | A rate per gram for each material and finish |
| Machine time | Printer wear, power and capacity on long or tall prints | A rate per printer hour, for parts where time does not track weight |
| Minimum job price | The fixed cost of handling any job: file checks, plating, packing | A floor so small jobs do not lose money |
| Setup fee | File preparation, test prints, custom profiles | Per job or per new design |
| Post-processing fee | Support removal, sanding, inserts, assembly | Per part, by time |
| Failure buffer | Reprints and material lost to failed prints | A percentage on material and time, from your own failure log |
A hypothetical example: say a part uses 60 g of PLA and 3 printer hours. With made-up rates of $0.08 per gram and $1.00 per printer hour, $2.00 of post-processing and packing labor and a 5% failure buffer, the cost-based price is $4.80 of material plus $3.00 of machine time plus $2.00 of labor, $9.80 in all, plus 5%, or about $10.29 before packaging, shipping and margin. These numbers are for illustration only. Your rates come from your own material costs, power, labor and failure logs.
On Printlooper, print shop pricing is typically per gram, with an optional minimum job price, failure rate buffer, setup fee and post-processing fee. Test your numbers with the income calculators, and see how to price a 3D printed product for the seller side of the same math.
Working with routed jobs on Printlooper
Routed jobs come with rules that protect designers' files and buyers' orders. Here is how they work at the time of writing (November 2026). How routing works covers more.
Setup and capacity
Onboarding covers your business profile, ship-from address, default lead time, printer fleet and bed sizes, material catalog, and Stripe Connect for payouts, which go out after orders are marked shipped. You can set a daily order cap, and the platform suggests one from your fleet size and beds. At the cap your shop drops out of the supplier list for new listings and print orders, while orders for listings that already use you still arrive. Marking your shop at capacity pauses new work and reroutes your pending orders once, so save it for a real pause such as a breakdown or a holiday.
Accepting and declining
Each assigned job includes the file through a signed link, the material and color, seller notes, the shipping address and any insert requirements. If you cannot do a job well, decline it with a reason. The order goes to the next eligible shop, up to three shops in total, and if none accepts, the order is cancelled and refunded. Declines do not count against your SLA score or rating, but they lower your acceptance rate. On a reroute, shops are ranked by rating, acceptance rate, SLA score and completed jobs. Location and price are not factors.
Deadlines, files and shipping
Your SLA record counts jobs that ship late or sit past their deadline, and the clock starts when the job reaches your shop, not when you open it, so check for new jobs at fixed times every day. File links last up to 7 days, and no new link is issued from 24 hours after the order is marked shipped. Buy labels through Shippo inside the job flow.
Employees, insurance and records
Employees and workplace safety
Once you hire, workplace safety law applies. OSHA lists employer responsibilities that include providing a workplace free from serious recognized hazards, following OSHA standards, keeping a written hazard communication program with safety data sheets readily available where hazardous chemicals are present, training workers in a language and vocabulary they understand, and posting the OSHA poster or your state plan's version. NIOSH's guide says that because 3D printing uses polymers, resins and solvents, the Hazard Communication Standard's requirements, including safety data sheets and training, must be met. Employers with more than 10 employees generally must also keep injury and illness records, with some industries exempt. Check OSHA and your state plan for what applies to you, and ask a safety professional when you are unsure.
In practice: write down your fire, resin and solvent procedures and train each person before they work alone, keep the SDS binder within reach, and provide the gloves, eye protection and other equipment the SDS lists.
Insurance
A farm carries property risk in printers, stock and the space, liability risk from products and premises, and, once you have staff, workers' compensation obligations that states regulate. Talk to a licensed insurance agent about what fits your work, and tell them your materials, fleet size and whether you sell your own products. If you fulfill orders on Printlooper, read the supplier insurance page, which describes commercial general liability insurance, including products-completed operations coverage, for print shops that fulfill orders for other sellers.
Records
- Job sheets: file, quantity, printer, profile version, spool lot, operator and ship date.
- Quality records: first article sign-offs, sample results and the defect log.
- A maintenance log for each printer.
- Material records: SDS files and supplier lot numbers.
- Safety records: alarm tests, extinguisher checks and training sign-offs.
- Financial records that clearly show income and expenses. The IRS notes that how long to keep a record depends on what it documents.
Frequently asked questions
How many printers do you need to start a print farm?
There is no set number. Start with as many printers as you can keep busy and inspect properly, often a handful, and grow when your logs show steady demand and on-time shipping. Adding printers before your workflow, quality checks and electrical capacity are ready multiplies problems along with output.
Is it safe to leave 3D printers running overnight?
Only if your printer maker's instructions allow it and the precautions are in place. Printers with heated beds should not run unattended without the fire precautions the maker recommends, such as smoke detection, a non-flammable surface and firmware thermal runaway protection switched on. Some makers say never to leave a printer unattended while it is on, and then you should not. Add cameras and a remote power cutoff, keep flammables away and follow a written policy.
Does a 3D print farm need ventilation?
Yes. NIOSH reports that 3D printers can release ultrafine particles and VOCs, and it ranks engineering controls such as ventilation, enclosures and HEPA filtration above personal protective equipment. Use a separately ventilated print room, enclosures with suitable filtration or exhaust, and keep people out of the room except when they need to be there. Resin printing needs its own ventilated space.
How do you do quality control on 3D prints?
Inspect the first part of every job against the spec, then sample the batch on a written rule, such as the first part from each printer, every tenth part and the last. Measure critical dimensions with calipers, test-fit hardware, check visible faces, photograph every order and log each defect with its cause, printer, profile and spool.
How do you calculate print farm capacity?
Multiply printers by the hours they can run with someone available, reduce that for changeovers and maintenance, then reduce it again for failed prints. Divide the good hours by print time per part to get parts per day. Check whether post-processing and packing labor is the real limit, and set your order cap below the result.
How should I price print farm jobs?
Most shops combine a per gram rate with a charge for machine time on long prints, a minimum job price, setup and post-processing fees, and a buffer for failed prints taken from their own logs. Add packaging and overhead, then compare the result with what buyers pay for similar parts. Recalculate when material or power costs change.
Do I need insurance for a 3D print farm?
Insurance needs depend on your work, location and contracts, so ask a licensed insurance agent. Print farms commonly look at property coverage for equipment and stock, general and product liability, and workers' compensation once they have employees. Tell the agent what materials you use, how many printers you run and whether you sell your own products.
Further reading
Sources
- NIOSH: Approaches to Safe 3D Printing (PDF)
- Bernatikova et al., Int J Environ Res Public Health (2021): Characterization of Ultrafine Particles and VOCs Emitted from a 3D Printer
- U.S. Fire Administration: Appliance and Electrical Fire Safety
- U.S. Fire Administration: Smoke Alarms
- OSHA: Portable Fire Extinguishers, Extinguisher Basics
- OSHA: Employer Responsibilities
- Prusa Research: Thermal Runaway
- Prusa Research: Extruder blob (unattended printing note)
- Prusa Research: Drying filament
- Formlabs: Safety with Formlabs SLA printers
Put your print farm on the Printlooper network
Set up your fleet, materials and pricing, choose a daily order cap, and accept the routed jobs that fit your farm.
Become a print shop