How to finish 3D prints: sanding, priming, painting and smoothing
A practical finishing workflow for FDM and resin prints, from support removal and sanding to primer, paint and clear coat, with the safety steps each stage needs and how to keep finishing consistent across a product run.
By Printlooper Team · Published · 24 min read
Key takeaways
- Decide the finish level before you pick up sandpaper. Each step from cleaned to fully painted adds hands-on time to every unit, so match the level to what the part is for.
- Sanding dust, aerosol paint, solvents, two-part fillers and uncured resin each need their own protection. An N95 respirator filters particles, not vapors, so read the safety data sheet for the respirator it calls for.
- Sand wet with light pressure, from about 120 to 220 grit up to 320 before primer. Friction heat softens PLA, smears it and clogs the paper.
- Filler primer hides layer lines: spray thin coats, wet sand at 320 to 400 grit and repeat until no lines show under raking light.
- A UV-resistant clear coat slows fading, but it does not turn PLA into an outdoor material, add strength or make a print safe for food.
- Wash, dry and cure resin parts fully before you sand them, and never pour resin, solvent or paint waste down a drain.
A print straight off the printer shows how it was made: layer lines, support scars, a seam running up one side. For many products that is fine. For a cosplay prop, a display piece or a product with a painted logo, finishing is the difference between a print and a product people want to keep.
This guide is for sellers who need every unit to look like the listing photo, designers who want to show a model at its best, print shops that offer finishing, and buyers deciding whether to finish a part themselves. It covers each stage in order, with the safety steps each one needs, and ends with a checklist for every finished part.
The numbers are typical starting points. Paint, primer, filler and resin makers set the real limits for their own products, so read the label and the safety data sheet (SDS) for anything you use, and test on a scrap print before a part that matters.
Choose a finish level before you start
Finishing is a series of steps, and each one adds time to every unit. Decide how far to go before you start, based on what the part is for and who will see it. A cable clip does not need paint. A painted helmet does not need its inside sanded smooth.
| Level | What it involves | Hands-on time per part | Worth it when |
|---|---|---|---|
| Raw | Off the bed, nothing else | Under 1 minute | Internal parts, fit tests and early prototypes |
| Cleaned | Supports, strings, blobs and sharp edges removed | 2 to 10 minutes | Functional parts and most everyday products |
| Sanded | Support scars and layer lines sanded down on visible faces | 15 to 45 minutes | Parts people handle, or parts that will get one color or a clear coat |
| Primed | Filler primer sprayed and sanded smooth, often in two or three rounds | 30 to 90 minutes | Anything that will be painted, or where layer lines must disappear |
| Painted | Base color, detail colors and masking | 30 minutes to several hours | Display pieces, props, figures and branded products |
| Painted and sealed | Paint protected by a matte, satin or gloss clear coat | Add 10 to 20 minutes | Parts that get handled often or live outdoors |
Two questions settle most decisions. Will anyone see or touch this face? Will the next step change how the product is used or what someone would pay for it? If the answer to both is no, stop at the level before.
Safety first: dust, sprays, solvents and resin
Most finishing hazards come from the products you use, not the print. Each product has a label and a safety data sheet (SDS), the maker's document listing hazards, protective equipment, storage and disposal. Read both before you open something new, and treat the SDS as the authority over any guide, this one included.
| Hazard | Where it comes from | Basic controls |
|---|---|---|
| Sanding dust | Dry sanding plastic, filler, primer and cured resin | Sand wet where you can, wear eye protection and a particulate respirator, and clean up with a damp cloth instead of sweeping |
| Spray mist and solvent vapor | Aerosol primers, paints and clear coats, and airbrushing | Spray outdoors or with strong cross ventilation, and wear the respirator and gloves the SDS lists |
| Flammable solvents | Isopropyl alcohol (IPA) for resin, thinners, cleanup solvents | Small containers with lids on between uses, no sparks or flames nearby, gloves and eye protection |
| Two-part fillers and coatings | Body filler, epoxy putty, brush-on epoxy coatings | Mix only what you can use in the working time, wear gloves and eye protection, ventilate, and expect the mix to heat up |
| Uncured resin | Liquid resin, unwashed prints, resin-soaked towels | Nitrile gloves every time, eye protection, and soap and water if resin touches skin |
| Fire | Aerosols, solvents, solvent-soaked rags, heaters and heat tools | Work away from heaters, pilot lights and sparks, store flammables closed and cool, never leave heat unattended |
Respirators: particles and vapors are different
A disposable N95 respirator filters particles. NIOSH, the US agency that approves respirators, states plainly that N95s and other filtering facepiece respirators do not protect against gases or vapors, so they do nothing for paint and solvent fumes. For vapors, NIOSH describes reusable elastomeric half-mask respirators fitted with the appropriate cartridge. Which cartridge you need, and whether you need a particulate filter as well, is in the product's SDS. Both types are tight-fitting and designed to seal against your face, so follow the maker's fitting instructions: air that leaks around the edge skips the filter.
Set up the space
- Spray outdoors on a calm day, or in a space with strong cross ventilation. A closed garage or spare room is not enough.
- Keep sprays, solvents and rags away from heaters, furnaces, water heaters and anything with a pilot light or spark.
- Keep children and pets out of the area until coatings are dry and waste is put away.
- Cover the work surface, and keep finishing out of kitchens. Never use food containers, food prep surfaces or kitchen tools.
- Keep products in their original labeled containers and never mix leftovers, as the EPA advises for household hazardous products. Keep each SDS where you can reach it quickly.
Remove supports and clean up the part
Clean support removal saves sanding later. Let the bed and the part cool fully before you remove it, since warm PLA bends and support scars tear deeper. Wear eye protection: support material snaps and small pieces fly.
- Remove the large pieces first Work large support blocks loose by hand or with pliers, from the outside in. Rock them gently until the interface lets go instead of levering against a thin feature.
- Cut, do not tear, at the surface Use flush cutters to cut support stubs close to the surface, then trim what is left with a sharp hobby knife. Cut away from your hand and body, and keep the part on a bench, not in your palm.
- Deburr edges and holes A deburring tool takes the sharp lip off edges and the first layer. Turn a drill bit of the right size through holes by hand to clear them to size without melting the walls.
- Remove strings and blobs Snip strings and slice blobs off with a blade held flat to the surface. Scrape a seam bump flat the same way, with the blade at a low angle.
- Fix elephant's foot The first layers often bulge slightly outward, which is called elephant's foot. Chamfer it with the deburring tool or a fine file so the part sits flat and fits its partners.
- Inspect under raking light Hold a light low across the surface. Scars, blobs and gaps cast shadows that overhead light hides. Mark anything that needs filling.
If every unit needs 10 minutes of scar removal, fix the cause before the next batch. Support settings and orientation decide how much cleanup a part needs (How to 3D print covers both), and overhangs kept under 45 degrees, as in Design for 3D printing, leave fewer faces to clean.
Fill gaps, seams and pinholes
Sanding takes high spots down. Filler brings low spots up: gaps between glued parts, sink marks, pinholes, deep layer lines and support scars. Pick the lightest filler that does the job, because every filler adds a sanding step.
| Filler | Best for | Notes |
|---|---|---|
| Filler primer (spray) | Layer lines and fine scratches | Builds in thin layers you sand back. Covered in the primer section below |
| One-part spot or glazing putty | Pinholes, small scratches and shallow dents | Spreads thin and sands easily. Thick layers shrink and crack, so build in thin passes |
| Two-part body filler | Gaps at seams, deep scars, reshaping edges | Mixed with its hardener in the ratio on the label. Sets in minutes and sands hard |
| Two-part epoxy putty | Rebuilding broken details, filling large gaps, sculpting | Kneaded together in the label's ratio. Longer working time, very hard once cured |
| Brush-on epoxy coating | Coating a whole part to bury layer lines | Self-levels into a hard shell. Thin coats only, and it softens fine detail |
| Thin cyanoacrylate (CA) glue | Hairline cracks and narrow seam gaps | Wicks into gaps and sands flush. Use with ventilation and keep it off skin |
Working with two-part products
Two-part fillers and coatings cure by a chemical reaction that gives off heat. Smooth-On's guidance for its XTC-3D coating, made for 3D prints, is a useful example: a 10 minute pot life once mixed, a single coat under 1/64 inch (about 0.4 mm) for most prints, no mixing in glass or foam containers, and a warning that a large mixed mass can get hot enough to burn skin or ignite nearby combustible materials. Measure the ratio on the label exactly, since a wrong ratio can stop the product curing properly. Mix small batches, wear the gloves, eye protection and respirator the SDS lists, and let each layer cure as directed before sanding.
Gluing split parts
Glue split parts before you fill, so the seam is filled once. CA glue bonds most filaments quickly, and a slow-curing two-part epoxy gives more time to align large parts. Tape or clamp the parts, wipe off squeeze-out before it cures, and let the glue cure fully before you sand across the seam.
Find the low spots with primer
Low spots are hard to see on bare colored plastic. A first light coat of primer shows them. Mark pinholes and dips with a pencil or marker, fill only those, sand them flat and prime again.
Sanding 3D prints: grits, wet sanding and pressure
Sanding is where most finishing time goes. Three habits make it faster: start with the right grit, keep the paper wet, and let the abrasive do the work instead of pressure.
| Goal | Start | Finish | Notes |
|---|---|---|---|
| Remove support scars and blobs | 120 to 180 grit | 220 grit | Sand only the scarred area. A sanding stick or file keeps edges crisp |
| Flatten layer lines before primer | 150 to 220 grit | 320 grit | Stop when lines are faint and let filler primer do the rest |
| Smooth filler primer | 320 grit, wet | 400 grit, wet | Sand until the guide coat is gone. Small sand-through spots to plastic are normal |
| Prepare for gloss paint or clear | 400 grit, wet | 600 to 800 grit, wet | Gloss shows every scratch underneath, so finish wet and fine |
| Polish clear or glossy resin | 600 grit, wet | 1,500 to 3,000 grit or finer, wet | Formlabs notes parts turn glossy around 3,000 grit and reflective near 12,000 grit |
Wet sanding controls dust and heat
Wet sanding means using waterproof sandpaper (sold as wet or dry paper) dipped in water, or with a little water on the part. The water carries dust away as a slurry instead of into the air, cools the surface and keeps the paper from clogging. Prusa's material guide says sanding PLA needs water cooling. Rinse the paper often, wipe the slurry away with a damp cloth, keep water away from embedded electronics, and let the part dry completely before primer or paint.
Light pressure, because friction softens PLA
PLA gets soft and deforms above about 60°C (140°F), according to Prusa's material guide, and friction from hard sanding or a fast rotary tool gets there quickly. The plastic smears, gums up the paper and leaves a rough, melted patch that takes longer to fix than the scar did. Use light pressure, let the grit cut, and change the paper as soon as it loads up. With a rotary tool, use its lowest speed, keep it moving and stop as soon as the plastic looks shiny or soft. PETG and ASA sand wet or dry, but the same light-pressure rule keeps them from smearing.
Technique that saves time
- Back flat faces with a sanding block or stick so you do not round over edges and corners.
- Change sanding direction between grits, so you can see when the previous grit's scratches are gone.
- Use a guide coat: a light mist of contrasting primer or a pencil scribble. Sand until it disappears, and whatever marks remain are low spots.
- Wrap paper around a dowel or use sanding sponges for curves and inside corners.
- Skip or mask faces that must fit something. Sanding removes material, and a fit surface sanded by 0.1 mm can turn a snug fit loose.
Filler primer and primer
Primer does two jobs: it gives paint something to grip and it shows you what the surface really looks like. Filler primer, often sold as high-build or sandable primer, goes on thicker and fills fine layer lines and scratches as you sand it back. Regular primer is thinner and is meant for a surface that is already smooth, just before color.
- Clean and dry the part Wipe off sanding dust and slurry with a damp lint-free cloth and let the part dry completely. Handle it by hidden faces or with gloves, since skin oil can stop primer from sticking.
- Read the can Check that the label lists plastic among its surfaces, and that your temperature and humidity are inside the range it gives. Cold or damp air slows drying and can spoil the finish.
- Test on a scrap print Spray a failed print or offcut in the same filament first. Once it is dry, look for wrinkling, tackiness or poor grip before you commit a real part.
- Spray thin coats Shake the can as the label says and hold it at the distance it lists. Sweep past the part in steady passes that start and stop off the part, and build two or three light coats rather than one heavy coat that runs.
- Wait the recoat and sanding times Respect the times on the can. Sanding times differ between products, and a coat that feels dry on the surface can still be soft underneath.
- Sand and repeat Wet sand filler primer at 320 to 400 grit. Fill any pinholes that appear with spot putty, then spray again. Two or three rounds usually bury FDM layer lines from typical layer heights.
- Finish with a thin primer coat Before color, a final light coat gives an even base. Gray suits most colors, white brightens light and vivid colors, and black deepens dark and metallic finishes.
Primer will not hide a deep scar or a step at a seam. If a flaw survives two rounds of filler primer, go back to putty for that spot instead of stacking primer, which softens detail everywhere else.
Painting 3D prints: brush, airbrush and spray
Most paints sold for plastic work on primed prints: acrylic hobby paints, enamels and spray paints are all common. The method matters less than compatibility. Each layer has to bond to the one below without attacking it.
| Method | Best for | Watch out for |
|---|---|---|
| Brush | Details, small batches, figures and miniatures | Brush marks. Thin acrylics slightly and build two or three thin coats |
| Airbrush | Smooth gradients, even coats on medium parts, consistent batches | Needs thinned paint, a compressor and cleaning. The mist still needs ventilation and the respirator the SDS lists |
| Spray can | Even base colors and clear coats on larger parts | Limited color control, heavy overspray, and runs from coats that go on too thick |
| Paint pens and markers | Lettering, edges, panel lines and touch-ups | Ink bleeds along layer lines on unprimed prints |
Masking for clean color lines
Mask with low-tack painter's or hobby masking tape. Press the tape edge down firmly with a fingernail or a plastic tool, then seal it with a light coat of the color underneath, so any bleed is the same color as the base. Pull the tape back over itself at a low angle once the new color is dry to the touch, before it fully hardens, so the edge breaks cleanly. Liquid masking fluid covers curves and textures that tape cannot follow.
Test compatibility on a scrap print
A paint that grips one filament or primer well can wrinkle, stay tacky or peel on another, and a solvent-based clear sprayed over some water-based paints can lift or craze them. Keep failed prints in each filament and test every new primer, paint and clear combination on one. After the full cure time, drag a fingernail across it, then press tape on firmly and pull it off. If the paint stays put, write the combination down.
Thin coats and patience
Thin coats dry faster, keep detail sharp and cure harder. Wait the recoat time on the label between coats. Dry to the touch is not cured: labels list separate times for touch, handling and recoating.
Clear coats, UV protection and what a coating cannot do
A clear coat protects paint from scuffs and handling and sets the final sheen: matte, satin or gloss. Matte hides fingerprints and small flaws. Gloss shows every flaw underneath, so it needs the finest sanding.
- Match the clear to the paint. Many paint makers sell clears designed for their own paints, and the label says what it can go over. Test the pair on a scrap print.
- Spray inside the label's conditions. Krylon's UV-Resistant Clear Coating, for example, lists best results between 55 and 75°F with humidity below 60%. Humid air can leave a cloudy, milky finish.
- Build light coats. Formlabs recommends two to three spray coats in a dust-free space once a part is completely dry.
- Allow the full cure before packing. The same Krylon clear is dry to the touch in 10 minutes but lists 5 hours before handling. Parts packed early stick to bags and pick up texture.
- Check the surfaces on the label. That Krylon product, for example, does not list plastic among its surfaces, which is one more reason to test on a scrap print first.
UV resistance for outdoor items
Sunlight fades paint and breaks down some plastics. A clear labeled UV-resistant slows fading of the paint under it. It does not change the plastic. Prusa's material guides say PLA degrades under UV light and is not suited to outdoor use, while ASA suits outdoor use because of its high UV and temperature resistance. For a planter, sign or garden part, choose an outdoor material first and treat the clear coat as extra protection, not the fix. 3D printing materials compares the options.
What a coating does not do
A clear coat or epoxy coating does not make a print safe for food or drink contact. Whether a finished part suits food use depends on the plastic, the colorants, the coating, how the part was made and how it will be used, and a claim like that needs testing you would have to obtain. The safe default is to sell coated prints as decorative and say so in the listing. Likewise, a coating adds a hard shell, not a load rating.
Resin print post-processing
A resin print comes off the build plate coated in liquid resin and is not yet fully hardened. It needs washing, drying and curing before it is finished. Wear nitrile gloves whenever you handle liquid resin, unwashed parts or used solvent, as resin makers advise, and wash skin with soap and water if resin touches it. Resin makers publish settings for each resin, and those settings come before anything below.
- Wash Wash the part in isopropyl alcohol (IPA) or the wash solution your resin maker specifies, for the time it lists. Formlabs describes a two-stage wash: a dirty bath first and a cleaner one second. Keep lids on wash containers between uses.
- Dry completely Let the part dry fully before curing, with good ventilation and away from sparks and flames. IPA is flammable: NIOSH lists its flash point at 53°F, below normal room temperature, so its vapor can ignite in an ordinary room.
- Post-cure Cure the part with UV light, and heat where the maker says so, at the time and temperature listed for that resin. Settings differ widely between resins, so use the maker's current table rather than a general number. With an open UV lamp rather than an enclosed curing unit, follow the lamp maker's instructions and never look into the light.
- Remove supports Formlabs recommends post-curing most parts before removing supports so thin features keep their shape, but follow your own resin maker's advice. Clip supports with flush cutters, and wear eye protection, since cured resin chips are sharp.
- Sand cured parts only, wet Sand only parts that are washed and fully cured, and sand wet so resin dust stays out of the air. Start at 220 to 400 grit on support nubs and work up through the grit table above.
- Prime and paint Cured resin takes primer and paint well. Formlabs recommends a spray primer for an even coat and several thin coats of paint.
Resin waste
Formlabs advises curing small amounts of leftover resin in a transparent, labeled, resin-safe container left in sunlight, and curing resin-soaked paper towels in sunlight or UV light before throwing them away. It says cured, hardened resin and cleaned parts can go in household waste, but solvent that contains dissolved resin must never go down a drain or into household waste. How used IPA is collected depends on where you live, so check the SDS and your local household hazardous waste program.
Smoothing methods: what each one does
Smoothing means removing layer lines across a whole surface. There are several ways to do it, and they differ widely in time, skill and hazard.
| Method | Works on | Effort and result | Hazard |
|---|---|---|---|
| Sanding and filler primer | All filaments and cured resin | Slow by hand, full control, a paint-ready surface | Low with wet sanding, ventilation and the right respirator for spraying |
| Brush-on epoxy coating | Most filaments and cured resin | Quick to apply, a glossy self-leveling shell, softens fine detail | Moderate: two-part chemicals, skin contact and heat while curing |
| Changing how the part is printed | Parts you are about to print | Matte filament, finer layers, better orientation, or resin instead of FDM | The same as printing itself |
| Solvent vapor smoothing | Mainly ABS and ASA, using acetone | A glossy surface that loses sharp edges and fine detail | High: flammable or toxic vapor. Not taught here |
Whichever method you choose, plan for dimensional change. Coatings add thickness, sanding removes material, and resin parts shrink slightly as they post-cure. Keep coatings off faces that must fit, or design those fits with the finish in mind.
Finishing at product scale
Finishing one part is a craft project. Finishing fifty is a production process. Every minute of hands-on time is multiplied by the run, and every unit has to look like the photo the buyer saw.
Count the time per unit
Say a painted figure takes 45 minutes of hands-on sanding, priming and painting, and you value your time at $20 an hour. That is $15 of labor per unit before paint, primer, sandpaper and tape, and before the drying waits that stretch one unit across two or three days. These are hypothetical numbers. Run the same sum with your own timed parts before you set a price. How to price a 3D printed product covers the other costs.
Make it consistent
- Keep a reference sample of the finished product and judge every unit against it under the same light.
- Write a finish spec: grits, filler, primer, paint brand and color code, number of coats, clear coat, and every drying and cure time.
- Batch each step. Sand ten parts, then prime ten, so drying time overlaps with work on the next batch.
- Buy primer and paint in quantities that cover a whole run, since colors can shift between production batches.
- Dry parts on stands, and spray every part from the same angles.
- Log defects. If one face always needs extra filler, fix it in the design or the print settings instead of the finishing.
When to change the print instead of the finish
The cheapest finish is often the one you never do. A matte filament hides layer lines that a glossy one shows, and a textured surface hides them too. A gradient, dual color or sparkle filament can replace a paint job on decorative products. Finer layers, a better orientation or resin printing can remove most sanding (FDM vs resin vs SLS compares the processes). Weigh the hands-on minutes per unit against a little more print time or a different material.
Finished-part quality checklist
Check every finished unit before it is packed, with the reference sample beside you and a light you can hold low across the surface.
Before a finished part ships
- No support stubs, strings, blobs or sharp edges anywhere a hand touches.
- Holes, slots and mating faces still fit their partner part or hardware after finishing.
- No visible layer lines on faces the finish spec says are smooth, checked under raking light.
- No pinholes, and no spots where primer was sanded through showing under the paint.
- Even paint coverage with no runs, drips, orange peel texture or dust nibs.
- Masked color lines are crisp, with no bleed or lifted paint.
- Clear coat sheen is even, with no cloudy or milky patches.
- Every coating is past the handling time on its label, with no tacky spots and no strong solvent smell.
- Resin parts are washed, cured and free of sticky residue.
- Color and finish match the reference sample and the listing photos.
- The listing describes the finish honestly and makes no food-contact, outdoor or strength claims you cannot back up with testing.
Frequently asked questions
How do you finish 3D prints?
Remove supports and clean up the part, fill gaps and seams, then sand from about 120 to 220 grit up to 320. Spray filler primer, wet sand it at 320 to 400 grit and repeat until no layer lines show. Paint in thin coats and protect the paint with a clear coat. Stop at the level the part needs, and read each product's label and safety data sheet before you start.
What grit sandpaper should I use on 3D prints?
Start at 120 to 180 grit for support scars and blobs, or 150 to 220 grit for layer lines, then move up to 320. Wet sand filler primer at 320 to 400 grit. For gloss paint or a gloss clear coat, finish at 600 to 800 grit, wet. Resin parts can go much finer: Formlabs notes a glossy surface around 3,000 grit. Use light pressure so friction does not soften the plastic.
Do you need to prime PLA before painting?
Paint will go on bare PLA, but primer helps it grip, shows flaws before color goes on, and filler primer hides layer lines. For a smooth painted product, spray filler primer, wet sand it at 320 to 400 grit and repeat until no lines show. Check that the primer's label lists plastic, and test it on a scrap print in the same filament before a real part.
What paint works on 3D prints?
Acrylic hobby paints, enamels and spray paints made for plastic all work on primed prints. Acrylics are the easiest to brush and clean up, and spray paint gives even coats on larger parts. Compatibility between layers matters most, so test each primer, paint and clear combination on a scrap print, wait the full cure time, then check grip with a fingernail and a strip of tape.
How do you smooth 3D prints without acetone?
Wet sand the part, then build and sand filler primer until the layer lines disappear. A brush-on two-part epoxy coating also buries layer lines in a hard, glossy shell, at the cost of some fine detail. For future prints, a matte filament, finer layers, a better orientation or resin printing reduce how much smoothing you need. Solvent vapor smoothing is hazardous and is not covered here.
How do you post-process resin prints?
Wearing nitrile gloves, wash the print in isopropyl alcohol or the wash solution your resin maker specifies, let it dry completely, then post-cure it at the time and temperature the maker lists for that resin. Remove supports, then wet sand only fully cured parts. Never pour resin or used solvent down a drain: cure small amounts of waste resin and follow the SDS and your local disposal rules.
How do I protect myself when sanding and painting 3D prints?
Sand wet where you can, wear eye protection and a particulate respirator for dust, and clean up with a damp cloth. Never sand uncured resin. An N95 respirator filters particles only, so it does nothing for paint or solvent vapor. For spraying, wear the respirator the product's safety data sheet lists, work outdoors or with strong ventilation, keep flames and heaters away, and keep children and pets out.
Does a clear coat make a 3D print safe for food?
No. A clear coat seals the surface and protects paint, and a UV-resistant clear slows fading outdoors, but it does not make a print safe for food or drink contact and it does not add strength. Food-contact suitability depends on the plastic, colorants, coating, production and use, and a claim like that needs testing you would have to obtain. Sell coated prints as decorative unless you have that evidence.
Further reading
Sources
- Prusa Knowledge Base: PLA
- Formlabs: Guide to post-processing and finishing SLA resin 3D prints
- Formlabs Support: Best practices for post-curing prints
- Formlabs Support: Disposing of resin
- Smooth-On: XTC-3D coating for 3D prints
- Krylon: UV-Resistant Clear Coating
- NIOSH: Types of respirators and masks
- NIOSH Pocket Guide: Isopropyl alcohol
- NIOSH Pocket Guide: Acetone
- EPA: Household hazardous waste
Compare finishes before you finish by hand
Upload an STL or 3MF, pick a material, color and finish, and compare all-in prices from approved print shops. No account needed.
Order a print