FDM vs resin vs SLS: which 3D printing process suits your design

How filament, resin and nylon powder printing differ, which products suit each one, the design rules that change between them, and how to move a product from prototype to production.

By Printlooper Team · Published · 23 min read

Key takeaways

  • FDM is the default for large, practical parts such as brackets, organizers and planters, because filament is cheap and build volumes are big, but layer lines show and parts are weakest between layers.
  • Resin (SLA, MSLA and DLP) prints layers as fine as 0.025 to 0.05 mm, so it wins on miniatures, jewelry masters and small figures, but standard resins are brittle and parts need washing, post-curing and usually supports.
  • SLS and MJF fuse nylon powder with no supports at all, which makes them a strong fit for snap fits, living hinges, print-in-place mechanisms and small production runs.
  • Design rules shift by process: a typical supported wall drops from 0.8 mm on FDM to 0.5 mm in resin, and the smallest hole goes from 2 mm on FDM to about 0.5 to 0.8 mm in resin and 1 to 1.5 mm in SLS.
  • Cost follows different levers on each process: print time and height on FDM, height, volume and supports in resin, and bounding volume and nesting in a powder bed.
  • Prove fit with a cheap FDM print first, then move to resin or nylon powder only when the product needs the detail, the strength or the volume.

FDM, resin and SLS are the three 3D printing processes you will meet most when you design, sell or order printed products. Each builds a part layer by layer, but they fail in different ways and reward different shapes. A miniature that looks crisp in resin loses most of its face at 0.2 mm FDM layers.

This guide is for designers picking a process for a new model, sellers deciding which version of a product to list, and buyers ordering a print who want the right material family. It explains how each process works, compares them side by side, lists the designs that suit each one and the ones to avoid, and gives the design rules and cost drivers you need to make a part that prints well on the process you pick.

How FDM, resin and powder-bed printing work

All three processes slice a 3D model into thin horizontal layers and build the part one layer at a time. What changes is how each layer turns solid. That one difference explains almost everything else in this guide: detail, strength, finish, supports and cost.

How each process builds a layer: a nozzle draws filament, light cures resin under a part that hangs from the plate, or a laser fuses powder that also supports the part.

FDM: melted filament through a nozzle

Fused deposition modeling (FDM, also called FFF for fused filament fabrication) pushes plastic filament through a heated nozzle and draws each layer as a series of lines. The nozzle is usually 0.4 mm wide and layers are usually 0.1 to 0.3 mm tall, with 0.2 mm as the common default. Common materials are PLA, PETG, ABS, ASA and TPU. Each line is a separate bead of plastic welded to the one below, so layer lines are visible and the bond between layers is the weakest direction of the part.

Resin: liquid photopolymer cured by light

Resin printers, a family called vat photopolymerization, cure liquid resin with ultraviolet or near-ultraviolet light. SLA (stereolithography) traces each layer with a laser. DLP (digital light processing) flashes a whole layer at once with a projector. MSLA (masked SLA, often sold as LCD printers) shines light through an LCD screen that masks each layer, and many desktop resin printers work this way. Layers usually range from 0.025 to 0.1 mm, with 0.05 mm a common default, and the smallest feature is set by the laser spot or the screen pixel, which is tens of microns. On most desktop machines the part grows upside down from a build plate that lifts after each layer to let fresh resin flow under it.

SLS and MJF: nylon powder fused in a heated bed

Selective laser sintering (SLS) spreads a thin layer of powder, most often nylon (PA12 or PA11), across a heated bed and fuses each cross section with a laser. Multi Jet Fusion (MJF) spreads the same kind of powder, prints a fusing agent onto it with inkjet heads and fuses the whole layer with infrared heat. In both, the loose powder around the part holds it up while it prints, so neither needs supports. Layers are usually 0.05 to 0.2 mm, often around 0.1 mm. When the build finishes, the whole block of powder cools slowly, which can take a large share of the total job time, then the parts are dug out, cleaned of powder and media blasted.

SLS and MJF parts behave much the same, so most design advice treats them as one family. The visible differences are color and surface. Most MJF parts come out gray and are often dyed black, though HP also makes a machine that prints white. SLS color depends on the powder: some nylons print white and others gray. White parts take the widest range of dye colors, while gray parts dye only to darker shades.

FDM vs resin vs SLS at a glance

Use this table as a first filter. If one row rules a process out for your product (a 400 mm helmet will not fit most resin printers, and a 25 mm miniature loses its face on FDM), you have your answer before you open CAD.

FDM, resin and SLS/MJF compared
FactorFDM (filament)Resin (SLA, MSLA, DLP)SLS and MJF (nylon powder)
Typical layer height0.1 to 0.3 mm, often 0.2 mm0.025 to 0.1 mm, often 0.05 mm0.05 to 0.2 mm, often about 0.1 mm
DetailGood above about 1 mm. Fine text and faces soften.Highest. Crisp edges, fine text and small faces.Good. Sharp edges round slightly and the grain hides fine texture.
Typical accuracyAbout ±0.5%, and on small parts roughly ±0.2 to 0.5 mm depending on the printerAbout ±0.15% on small partsAbout ±0.5%, or ±0.3 mm on small parts
Strength and how it failsStrong along layers, weakest between them. Fails by splitting along a layer line.Standard resin is stiff but brittle and snaps or cracks. Tough resins bend more.Tough, with far less difference between directions than FDM. Nylon bends before it breaks.
Surface finishVisible layer lines and a seam. Flat tops are smooth, curved tops show steps.Smooth, close to a molded look. Small nubs where supports touched.Matte and slightly grainy, like fine sandpaper. Even on every face.
Typical build sizeAbout 180 to 350 mm per side on desktop machines, more on large-format printersAbout 150 to 220 mm on the longest side on most desktop machines, about 350 mm on large-format onesAbout 165 x 165 x 300 mm on benchtop machines, 380 mm or more on industrial ones
SupportsNeeded for overhangs past about 45 degrees from vertical and for long bridgesNeeded on most parts, usually with the part tilted on a field of thin supportsNone. Loose powder holds the part.
Post-processingRemove supports, then sand, prime and paint if neededWash off uncured resin (often in isopropyl alcohol), post-cure, clip and sand support marks, all per the resin maker's instructionsDig out of the powder, media blast clean, then dye, smooth or paint if needed
Color optionsAny filament color, several colors in one part on multi-material printers, plus silk, matte, glow and sparkle filamentsUsually one color per part: gray, white, black, clear or tinted. Painted for full color.White or gray depending on the powder (most MJF parts are gray), often dyed black. Dyed or painted for other colors.
What drives costPrint time, which follows height, volume and infillHeight, resin volume and the labor of supports and finishingBounding volume in the build chamber and how tightly parts nest
Common materialsPLA, PETG, ABS, ASA, TPUStandard, tough, flexible and castable resinsPA12, PA11, glass-filled nylon, TPU and polypropylene powders

FDM: designs that suit it and designs to avoid

FDM is the workhorse. Filament is cheap, machines are everywhere, build volumes are large and the material list covers rigid, heat-resistant, UV-resistant and flexible parts. Its limits come from the nozzle and the layer bond. Nothing thinner than one line of plastic, about 0.4 mm, prints, and loads that pull layers apart break parts first.

Designs that suit FDM

  • Brackets, mounts and hooks. Flat-sided parts that print with the load running along the layers. A wall hook printed on its side is much stronger than the same hook printed upright. Test samples before you state any load.
  • Desk organizers and drawer inserts. Boxy shapes with vertical walls print fast and need no supports. Phone stands follow the same logic.
  • Planters and vases. Round, thin-walled shapes print well, including single-wall vase mode for decorative pieces. Anything that holds soil needs a real wall and a drainage plan. See planters.
  • Large decor and lamp shades. Shades, wall art and sculptures up to the size of the bed, in matte, silk or gradient filaments.
  • Cosplay armor and helmets. Big curved parts split into sections that fit the bed, then sanded, primed and painted. See cosplay helmets.
  • Flexible parts. Bumpers, grips, feet and sleeves in TPU.

Designs to avoid on FDM

  • Features thinner than 0.4 mm. Hair strands, thin text strokes and fine filigree either vanish or turn to strings.
  • Faces and miniatures under about 50 mm. Layer steps of 0.1 to 0.2 mm blur most facial detail. Resin does this job.
  • Parts loaded across the layers. A tall thin post, or a clip that flexes against the layer lines, snaps along a layer. Reorient it or move to nylon powder.
  • Downward-facing curves. The underside of a sphere or dome needs supports, and supports leave a rough surface where they touch.
  • Closed internal channels. Any hole that needs supports inside it where no tool can reach.

Material choice matters as much as process on FDM. PLA starts to soften at around 55 to 60 °C and degrades in sunlight, so a PLA phone mount on a sunny dashboard can warp. PETG handles heat better, and ASA handles both heat and UV better still. Compare them in the 3D printing materials guide.

Resin: designs that suit it and designs to avoid

Resin trades size and toughness for detail. At 0.025 to 0.05 mm layers the steps are almost invisible, edges stay sharp and small raised text stays readable. The costs are a smaller build area, supports on most parts, messy post-processing and, with standard resins, brittleness. Uncured resin can also irritate skin and cause allergic reactions, so it is handled as its safety data sheet directs, with nitrile gloves, eye protection and good ventilation.

Designs that suit resin

  • Tabletop miniatures and busts. Faces, chainmail and sculpted cloth at 28 to 75 mm scale. See D&D miniatures.
  • Jewelry masters. Rings, pendants and charms printed in castable resin for lost-wax casting, or as masters for silicone molds.
  • Small detailed figures and collectibles. Display pieces that live on a shelf and get handled gently.
  • Artisan keycaps. Small, detailed and often painted or used as mold masters. See keycaps.
  • Fine scale models. Architectural pieces, vehicle details and master patterns that need very fine detail, where a 0.1 mm step would show.
  • Clear and translucent parts. Clear resin, sanded and coated, makes light pipes and windows much clearer than filament can.

Designs to avoid in resin

  • Anything bigger than the vat. On most desktop machines, parts past about 200 mm need splitting, and large flat areas tend to warp and peel.
  • Parts that flex or take impact. Standard resin clips, hinges and thin brackets snap. Tough resins help, but nylon powder or PETG does this job better.
  • Outdoor parts. Sunlight makes resin parts more brittle and changes their color over time, and Formlabs advises keeping functional resin parts out of direct sun for long periods. A UV-blocking paint or clear coat helps.
  • Large solid blocks. A solid 80 mm cube uses a lot of resin. Hollow it and add escape holes.
  • Thin flat panels. Plates and lids warp as they cure. Add ribs or a gentle curve.

SLS and MJF: designs that suit them and designs to avoid

Powder-bed nylon is the process for parts that have to work. With no supports, you can design shapes that are impossible on the other two: interlocking parts, enclosed mechanisms and dozens of parts stacked in one build. Nylon is tough and slightly flexible, and its strength varies far less with direction than an FDM part's, so orientation matters much less than on FDM.

Designs that suit SLS and MJF

  • Functional assemblies. Enclosures, housings, brackets and jigs that bolt together and carry loads. Test samples before you state a limit.
  • Snap fits. Nylon flexes and recovers, so a cantilever snap survives repeated use where PLA and standard resin crack.
  • Living hinges in nylon. A thin nylon web works as a hinge for boxes and cases. Protolabs suggests about 0.5 mm thick on MJF and 0.75 mm on SLS. Test a sample before you sell it.
  • Print-in-place mechanisms. Chains, gears in a housing, hinged boxes and articulated parts that come out of the powder already assembled.
  • RC and hobby parts. Mounts, arms and brackets that take crashes. See RC parts.
  • Small production runs. Tens to a few hundred identical parts nested in one build, each with the same strength and finish.

Designs to avoid in SLS and MJF

  • Glossy or brightly colored display pieces. The finish is matte and grainy, and color usually means dye or paint.
  • Large flat plates. Big thin panels warp as the build cools. Add ribs or curvature.
  • Sealed hollow volumes. Trapped powder adds weight and cost. Make the part solid or add at least two escape holes, 3.5 to 5 mm or larger per the shop's guide.
  • One large part on a tight budget. A single big part claims a large block of the build chamber, so FDM is usually cheaper for one-offs.
  • Very fine surface texture. Tiny text and sculpted skin texture blur into the grain. Resin keeps them sharper.

Design rules that change by process

Most design rules are the same idea on every process: walls thick enough to survive, holes big enough to stay open, gaps wide enough to move. The numbers change. These are safe starting points. Every machine and material differs, so print a test piece before you commit to a tight fit. The full rule set lives in design for 3D printing.

Design rules by process
RuleFDMResinSLS/MJF
Minimum supported wall0.8 mm0.5 mm0.7 mm
Wall for a product people handle1.2 to 2 mm1 mm or more, thicker for hollowed shells1 to 2 mm, about 2 mm for hollow parts
Smallest hole2 mm0.5 to 0.8 mm1 to 1.5 mm
Gap between moving parts0.3 to 0.5 mm0.2 to 0.5 mm0.3 to 0.7 mm
OverhangsUp to about 45 degrees from vertical without supports, more on well-cooled printersUsually supportedNo supports needed
Escape holes for hollow partsNot needed, hollowness is set by infillAt least two, 3.5 mm or largerAt least two, 3.5 to 5 mm or larger
Strongest orientationLoad along the layers, never across themAffects supports and surface more than strengthVaries far less with direction than FDM

How to read the numbers

  • A supported wall joins the rest of the part on at least two sides. Freestanding fins and posts need more, so thicken them or add a fillet at the base.
  • The smallest hole is the diameter that stays open and round. Holes that must fit a pin or screw closely tend to come out slightly small. Design them 0.1 to 0.2 mm larger and test, or drill them to size.
  • The gap between moving parts is the clearance on each side for print-in-place hinges and sliding fits. Go smaller for a press fit and test it. Powder-bed parts with thick walls need the top of their range. For parts made on machines you have never seen, use the top of the range too.
  • Escape holes let resin drain or powder pour out of a hollow part. Put them at opposite ends so one lets air in while the other drains.

What drives cost on each process

The same part can be cheap on one process and expensive on another. Know what each process charges for and you can design cost out before you ask for a quote.

FDM: print time and height

FDM cost is mostly machine time plus filament. Time grows with the volume of plastic laid down, the number of layers and the travel between separate islands of a layer. Height sets the layer count, so a 200 mm tall vase takes 1,000 layers at 0.2 mm, while the same shape split or laid down takes fewer. Most models print fine at 10 to 15% infill. Functional parts get more perimeter walls rather than more infill, because most of the strength comes from the walls.

Resin: height, volume and supports

On MSLA and DLP printers each layer cures in one exposure, so print time follows height, not how many parts share the plate. A plate of 20 miniatures takes about as long as one. Cost then follows resin volume and the labor of supports, washing, curing and cleanup. A hollowed figure uses a fraction of the resin of a solid one, and an orientation that needs fewer, smaller supports saves sanding time.

SLS and MJF: bounding volume and nesting

A powder-bed machine heats and spreads powder across the whole chamber on every layer, whether that layer holds one part or fifty. Operators fill the chamber by nesting parts in three dimensions, and many price each part partly by how much of the chamber it takes up. That makes the bounding box matter as much as the weight. A long thin frame or a large hollow ring claims a big block of the chamber and costs more than its few grams suggest, while small compact parts pack tightly and get cheap at volume.

Cost levers you control in CAD
Design choiceFDMResinSLS/MJF
Make the part shorterFewer layers, less timeFewer layers, the biggest time savingSmall effect per part, the build height is shared
Hollow it outUse lower infill insteadLarge resin saving, add escape holesSaves powder, add escape holes
Avoid steep overhangsFewer supports and less cleanupSupports remain, but fewer contact points helpNo effect, there are no supports
Make it compactSmall effectMore parts per plateLarge saving, more parts per build
Split a large partFits smaller, cheaper machinesOften the only way to fit the vatPieces nest instead of claiming one big box

Which process to use: a decision guide

Start with the product's main job and find the matching row. If two rows apply, the stricter one wins.

If your product is this, start with this process
If your product isStart withWhy
A bracket, hook, mount or organizerFDM in PLA or PETGCheap, fast and strong when the load runs along the layers
A planter, vase, lamp shade or large decor pieceFDMBig build volume and the widest choice of colors and finishes
Cosplay armor or a full-size helmetFDM, split into sectionsLarge pieces fit FDM beds and sand and paint well
A miniature, bust or small figureResinKeeps faces and fine texture that FDM layers blur
A jewelry master or ringCastable or high-detail resinSmooth surfaces and fine detail for casting or molds
A snap-fit case, clip or living hingeSLS or MJF nylonNylon flexes and recovers without cracking
A print-in-place mechanism or chainSLS or MJF, or FDM with generous gapsNo supports to trap the moving parts
An outdoor or in-car partFDM in ASA, or PETG for milder heat and sunASA resists heat and UV best of the common filaments. Avoid PLA and standard resin, and test in real conditions
A run of dozens of identical functional partsSLS or MJFParts nest in one build with the same strength and finish
A one-off prototype to check fitFDMThe fastest, cheapest way to hold the part in your hand

Questions to answer before you choose

  • Is the longest side over about 200 mm? Then most desktop resin printers are out unless you split the part.
  • Does any feature measure under 0.4 mm? Then FDM loses that feature.
  • Does the part flex, snap or take impact? Look at nylon powder or a tough filament first.
  • Will it live outdoors, in a car or near heat? Rule out PLA and standard resin.
  • Does it need a specific color without paint? FDM has the widest range.
  • Is the surface the product, as with a figure or a ring? Start with resin.
  • How many will you make? One or two favors FDM, and dozens of identical functional parts favor SLS or MJF.

Buyers with a finished file can keep it simple: pick the material family that matches the job, order the cheaper option first and step up only if it falls short.

Designing one product for more than one process

Sellers often want one design that can be made in PLA for price-sensitive buyers and in resin or nylon for a premium version. You can get close with one file if you design every feature to the strictest rule across the processes.

  1. Use the thickest wall Design walls at 1.2 to 2 mm. That meets the FDM product rule and is generous for resin and powder.
  2. Use the largest hole and gap Keep holes at 2 mm or more and moving gaps at about 0.5 mm, or up to 0.7 mm on thick parts headed for a powder bed. Some processes then run a little loose, which beats a hinge that fuses shut.
  3. Keep overhangs at 45 degrees or less Chamfer the undersides of ledges and horizontal holes instead of rounding them, so FDM prints them without supports. Resin and powder do not care either way.
  4. Give it a flat base A flat face sits on an FDM bed without supports or a brim, and it does no harm on the other two processes.
  5. Avoid sealed hollows Make the part solid or open, or add at least two 5 mm escape holes. That meets the powder rule and also covers resin.
  6. Split anything over about 200 mm Pieces that fit a desktop resin vat also fit most FDM beds and powder chambers. Add pins, keys or a dovetail so the pieces line up.
  7. Keep fine detail at 0.4 mm or more Detail finer than one FDM line disappears on filament. If the premium version needs finer detail, publish a separate resin version.

When one file cannot serve every process, publish separate versions with clear names, such as a hollowed resin version and a solid FDM version, so nobody has to guess which file to use.

From prototype to production

Most products should not start on their final process. Prove the shape and fit cheaply, then pay for detail or strength once you know the design works.

  1. Prove fit on FDM Print the first version in PLA at 0.2 mm layers. Check size, fit against mating parts, feel in the hand and proportions. Plan for more than one round.
  2. Lock the clearances Print a fit test coupon on the target process and adjust gaps and hole sizes to match it.
  3. Pick the production process Stay on FDM if layer lines are acceptable and the part is large. Move to resin when detail is what sells the product. Move to SLS or MJF when the part flexes, carries loads or ships in volume.
  4. Adapt the file Hollow it and add escape holes for resin or powder. Remove any supports you modeled in for FDM. Thin walls that were thick only for FDM if you want to save material.
  5. Order samples Order one or two parts on the production process and test them the way a customer will: drop them, flex them, assemble them, wash them and leave one in the sun.
  6. Quote the run Get per-unit prices at the quantity you plan to sell. Volume often changes which process wins once you pass a few dozen units.

A common path for a functional product is PLA prototypes, a PETG or ASA version for early sales, then SLS or MJF nylon once order volume justifies it. For a display product it is PLA to check scale and pose, then resin for everything you sell. The how to 3D print guide covers slicing and finishing for the prototype stage.

Ordering each process on Printlooper

If you want to compare processes on a real part, you can price it without owning any of these machines.

  • Single prints and small batches. When you order a print, you upload an STL or 3MF (up to 50 MB and up to 12 parts), preview it in the browser, and pick quantity, material, color, finish and print strength (display, functional or solid). Material families are PLA, PETG, ABS, ASA, TPU, resin and nylon, and choosing one filters to print shops that stock it. You compare all-in prices from approved print shops and pay on one page, with no account needed.
  • Larger runs. With production quotes you set the brief once (file, quantity, process, material and need-by date) and choose FDM, resin (SLA/DLP) or SLS/MJF. Approved production shops reply with a firm per-unit price and a lead time, and nothing is charged until you accept a quote.
  • Size limits. A file is refused at order time if no shop's printer bed can hold it. Design uploads are rejected if the longest side is over 500 mm or the smallest side is under 2 mm.

Volume pricing starts at 25 units and there is no minimum order, so a single sample and a first small batch go through the same page. There is no fixed lead time, because each print shop sets its own production time.

Frequently asked questions

Is resin printing better than FDM?

Neither is better overall. Resin is better for small, detailed parts such as miniatures, jewelry masters and figures, because its fine layers, often 0.025 to 0.05 mm, are nearly invisible. FDM is better for large, practical and low-cost parts such as brackets, organizers, planters and cosplay armor, and it offers far more colors and more impact-resistant materials than standard resin. Many makers use both: FDM for prototypes and big parts, resin for detail.

What is the difference between SLA and FDM?

SLA cures liquid resin with a laser one thin layer at a time, while FDM melts plastic filament and lays it down through a nozzle. SLA gives smoother surfaces and finer detail but needs supports, washing and post-curing, and standard resins are brittle. FDM builds bigger parts at lower cost, in more materials and colors, with visible layer lines and weaker bonds between layers.

What is the difference between MJF and SLS?

Both fuse nylon powder in a heated bed without supports and make tough parts with similar design rules. SLS fuses each layer with a laser. MJF prints a fusing agent with inkjet heads and fuses the whole layer with infrared heat. Most MJF parts come out gray and are often dyed black, while SLS color depends on the powder, and white SLS parts take the widest range of dye colors. For most designs they are interchangeable.

Which 3D printing process makes the strongest parts?

For most products, SLS and MJF nylon makes the toughest parts, because nylon flexes before it breaks and the parts vary far less in strength by direction than FDM parts. FDM parts in PETG, ASA or nylon filament can be very strong along their layers but split more easily between them. Standard resin is stiff but brittle. Tough resins narrow the gap without matching nylon for impact.

Which is cheapest: FDM, resin or SLS?

For a single part, FDM is usually cheapest because filament and machine time cost little. Resin is often competitive for small parts, since on MSLA and DLP machines a whole plate prints in about the time of one part, though washing and support removal add labor. SLS and MJF cost more for one-offs and become competitive for batches of small parts that nest tightly in one build. Compare real quotes, because the shape changes the answer.

Can resin prints be used outdoors?

Not well. Sunlight makes resin parts more brittle and changes their color over time, and Formlabs advises keeping functional or load-bearing resin parts out of direct sun for long periods. A UV-blocking paint or clear coat helps for display pieces. For parts that live outside, ASA filament, or PETG for milder conditions, is the safer choice. Test a sample in real conditions first.

Is SLS worth it for small production runs?

Often, yes. Because many parts nest in one build and need no supports, SLS and MJF can make tens or hundreds of identical small parts with consistent strength and finish and little hand work. The process suits snap-fit enclosures, clips, brackets and mechanisms. For one large part, or for display pieces where color and gloss matter, FDM or resin usually costs less.

Can the same 3D model be printed with FDM and resin?

Often, if every feature meets the strictest rule: walls of 1.2 to 2 mm, holes of at least 2 mm, moving gaps of about 0.5 mm, overhangs of 45 degrees or less and no sealed hollows. Detail finer than 0.4 mm will not survive FDM. When one file cannot serve both processes, publish a separate resin version, usually hollowed with escape holes.

Further reading

Sources

Price your part in more than one material

Upload an STL or 3MF, try PLA, resin or nylon, and compare all-in prices from approved print shops. No account needed.

Upload a file