3D printing materials guide: choosing PLA, PETG, ABS, TPU, nylon or resin

Compare the common 3D printing materials on strength, heat, outdoor use, ease of printing and safety, and match each product to the material that suits it.

By Printlooper Team · Published · 22 min read

Key takeaways

  • PLA is the default for indoor display parts, but it softens around 55 to 60 °C, so keep it out of hot cars and direct sun.
  • PETG is the everyday functional material. It is tougher than PLA and holds its shape to around 65 to 80 °C, depending on the brand.
  • ASA is the pick for parts that live outdoors, because it resists UV and holds its shape to around 90 to 100 °C.
  • TPU makes flexible parts, with 95A as the common grade, and nylon or carbon fiber nylon makes tough wear parts such as gears and hinges.
  • Dry PETG, TPU and nylon before printing in a filament dryer, never a kitchen oven used for food, and store every filament sealed with desiccant.
  • Do not sell 3D printed items as food safe or safe for children. Layer lines, additives, nozzles and coatings make food claims hard to back up, and children's products need third-party testing in the US.

Material choice decides whether a part survives its first summer in a car, its first drop on a tile floor or its first month in the garden. This guide is for designers choosing a material to design around, sellers deciding what to offer, buyers ordering a print and print shops that want a quick reference.

It starts with a quick picker and two comparison tables, then covers each material in depth, from PLA and its variants to resins and powder-bed nylon. After that come colors and finishes, drying and storage, safety, and a table of common products with the material that suits each. Figures are typical ranges, and the datasheet for the exact filament or resin always wins.

Quick picker: which material for which job

Start from what the part has to survive, not from whatever spool is already loaded.

Quick material picker by use case
Use caseBest pickAlso worksWhy
Indoor display pieces, figurines and decorPLAStandard resin for small detailEasy to print, crisp detail, widest color range, low cost
Miniatures and fine detailStandard or tough resinPLA at 0.12 mm layers for larger figuresResin layers of 0.025 to 0.05 mm capture faces and textures
Functional indoor parts such as brackets and holdersPETGPLA+ for light loadsTougher and less brittle than PLA, with more heat headroom
Parts outdoors in the sunASAPETG for light duty or shadeResists UV and holds its shape in heat
Parts inside a carASA or ABSPolycarbonate, nylonSunlit dashboards get hotter than PLA's softening point and close to PETG's
Flexible parts such as cases, bumpers and gasketsTPU 95AFlexible resin for small partsBends and springs back without cracking
Gears, hinges, clips and wear partsNylonPETG for light loadsTough and slippery, bends before it breaks
Stiff, light parts such as jigs and drone framesCarbon fiber nylonPolycarbonate, PETGHigh stiffness for its weight, holds dimensions
Large cosplay props and costume helmetsPLA or PLA+PETGLight, low warping, easy to sand and paint. Props only, never protective gear
Small production runs of tough partsSLS or MJF nylon (PA12)PETG or nylon on FDMNo supports, consistent parts, similar strength in every direction
Jewelry masters for metal castingCastable resinCastable filament for larger, less detailed piecesBurns out cleanly in an investment casting mold

Questions to answer before you pick

  • What is the hottest place this part will ever sit, such as a car, a windowsill or next to a motor?
  • Will it live outdoors or in direct sun?
  • Does it bend, flex, snap together or take impacts?
  • Does it rub against anything, like a gear or a hinge?
  • How small is the finest detail that matters?
  • Will it touch food or skin, or end up in a child's hands?
  • Does it need a particular finish or effect, such as matte, silk or glow?

Properties compared

Ratings are relative, for typical unfilled materials printed with sensible settings. Heat figures are approximate points where a part starts to sag under light load, mostly makers' heat deflection temperatures (HDT) at the lighter 0.45 MPa test load. Datasheets also quote HDT under a heavier 1.8 MPa load, or glass transition temperature (Tg), so compare like with like and check the datasheet for the exact product.

Printed strength depends as much on orientation, walls and settings as on the material. For anything that carries a load, print samples, test them in the real conditions with a wide safety margin, and do not sell a part as load rated without proper testing.

Strength, stiffness, impact and heat
MaterialStrengthStiffnessImpact resistanceHeat resistance (approximate)
PLAMedium to highHighLow, snaps rather than bendsSoftens around 55 to 60 °C
PLA+ or tough PLAMedium to highMedium to highMediumSimilar to PLA
PETGMediumMediumMedium to highAround 65 to 80 °C
ABSMediumMediumHighAround 90 to 100 °C
ASAMediumMediumHighAround 90 to 105 °C
TPU 95ALow, stretchesVery low, flexibleVery highVaries by grade, check the datasheet
NylonHighMediumVery highOften above 100 °C under light load, far lower under heavy load
Carbon fiber nylonHighVery highMedium to highUsually higher than unfilled nylon
PolycarbonateHighMedium to highVery highAround 110 °C
Standard resinMediumHighLow, brittleOften about 55 to 75 °C, depends on resin and post-cure
Tough or ABS-like resinMediumMediumMedium to highOften about 45 to 70 °C, depends on resin and post-cure
SLS or MJF nylon (PA12)HighMediumHighAbout 170 °C under light load, 85 to 95 °C under heavy load
Outdoor use, flexibility, ease of printing, fumes and cost
MaterialOutdoor and UVFlexibilityEase of printingFumes and ventilationRelative cost
PLAPoor, softens in sun and fadesRigidEasiestLow odor, ventilate the roomLow
PETGFair to goodSlight flexEasy, strings moreLow odor, ventilate the roomLow
ABSPoor, yellows and turns brittleSome flexHard, warps without an enclosureStrong styrene smell, needs filtering or ventingLow
ASAVery goodSome flexHard, warps without an enclosureStrong smell, needs filtering or ventingMedium
TPUFairVery flexibleModerate, slow and fussyLow odorMedium
NylonFair, absorbs moistureTough, bends before breakingHard, must be dry, warpsModerate, ventilateHigh
PolycarbonateFair to goodSome flexHard, very hot nozzle and enclosureModerate, ventilateHigh
Standard resinPoor, yellows and turns brittleRigidModerate, messy wash and cureResin odor, gloves and ventilationMedium
SLS or MJF nylonGood, best dyed blackSome flexProfessional machines, so ordered from a print serviceHandled by the print shopHigh for one-offs

For a side-by-side of the three materials most marketplace orders use, read PLA vs PETG vs ABS for marketplace orders.

PLA and its variants

PLA (polylactic acid) is the default filament for good reasons. It prints at low temperatures, barely warps, smells mild and comes in more colors than anything else. It is stiff and holds fine detail. Its weak points are heat and impact. It softens around 55 to 60 °C, so a PLA part on a dashboard or a sunny windowsill can sag, and it snaps rather than bends when dropped or overloaded.

Typical settings are a nozzle at 190 to 230 °C depending on the brand, a bed at up to about 60 °C and full part cooling after the first layers. Use it for display pieces, figurines, desk items, cosplay props, prototypes and indoor planters. PLA breaks down only in industrial composting facilities, not in a garden compost heap, so do not market prints as biodegradable or compostable.

Matte PLA

Matte PLA contains fillers that scatter light, which hides layer lines and fingerprints and gives a paint-like look. Many matte PLAs bond between layers noticeably less well than standard PLA, so keep them to decorative and lightly loaded parts.

Silk PLA

Silk PLA has additives that give a shiny, metallic sheen that shifts as light moves across it. It prints best a little hotter and slower than standard PLA, strings more and has noticeably weaker layer bonding. It is for vases, decor and display models, not for parts that carry load.

PLA+ and tough PLA

PLA+ has no standard definition. Each maker modifies PLA differently, usually with impact modifiers, to make it less brittle. Some versions are much tougher than standard PLA and some differ very little, and heat resistance stays about the same. Read the datasheet and test before relying on it.

Filled and effect PLAs

Wood, stone, glow-in-the-dark, sparkle and carbon fiber PLAs mix particles into the plastic. Many of those fillers, including carbon fiber and many glow-in-the-dark blends, are abrasive and wear out a standard brass nozzle fast. Print abrasive filaments with a hardened steel nozzle, and consider a 0.6 mm nozzle for wood fill to reduce clogs.

PETG

PETG (polyethylene terephthalate glycol) is the workhorse for functional parts. It is tougher and less brittle than PLA, flexes a little before it breaks and holds its shape to around 65 to 80 °C, depending on the brand. It copes with moisture and sun better than PLA, though ASA lasts longer in strong sun.

It has quirks. PETG strings more than PLA, so dry it and tune retraction. It bonds so strongly to smooth PEI that it can damage the sheet, so print it on textured PEI or use glue stick as a release layer. It wants less cooling than PLA, from off to about 50% fan depending on the maker, because heavy cooling weakens the bond between layers. Typical settings are a nozzle at 230 to 260 °C and a bed at 70 to 90 °C.

Use PETG for brackets, mounts, enclosures, planters, cable management, tool holders and anything handled every day. Translucent PETG also makes good light diffusers. The PETG material page covers ordering it.

ABS and ASA

ABS (acrylonitrile butadiene styrene) is the plastic in many molded consumer products. Printed, it is tough, takes impacts well and holds its shape to around 90 to 100 °C. ABS and ASA dissolve in acetone, and some people smooth parts with acetone vapor, but acetone is highly flammable and its vapor irritates eyes and airways. It is not a beginner technique, and this guide does not cover it.

The catch is shrinkage. ABS warps and splits between layers in a cold or drafty room, so it needs an enclosed printer, a bed at 90 to 110 °C, little or no part cooling and a nozzle around 240 to 265 °C. It also gives off a strong styrene smell and fine particles, so print it in an enclosure with a filter or with venting to the outside.

ASA (acrylonitrile styrene acrylate) prints much like ABS and needs the same enclosure and ventilation, but it resists UV. ABS turns yellow and more brittle in sunlight, while ASA keeps its color and toughness outdoors far longer. That makes ASA the default for outdoor fixtures, garden parts, signs and house numbers. Both handle car interiors better than PLA or PETG. The ABS material page covers ordering ABS parts.

TPU and flexible filaments

TPU (thermoplastic polyurethane) makes rubbery parts that bend, stretch and spring back. Flexible filaments are graded on the Shore A hardness scale, where a higher number is harder. 95A is a common grade, firm but bendable, and among the easiest flexible filaments to print. Softer grades, such as 85A and below, bend more easily, and the softer the filament, the harder it is to print.

Print TPU slowly, around 20 to 40 mm/s unless the maker gives a higher speed, with low retraction and a nozzle at about 210 to 245 °C. A direct-drive extruder helps a lot, especially with soft grades, because soft filament buckles and tangles in a long feed tube. TPU absorbs moisture readily, so dry it before printing.

Use TPU for phone cases, bumpers, feet, gaskets, seals, watch straps, cable strain reliefs and RC tires. Infill and wall count change how soft the finished part feels, so you can tune a product's squish in the slicer. The TPU material page has more.

Nylon, carbon fiber nylon and polycarbonate

Nylon

Nylon (polyamide, or PA) is tough, slippery and wear resistant. It bends before it breaks and survives repeated flexing, which makes it the material for gears, hinges, clips, bushings and working brackets. It is also very hygroscopic. Nylon pulls moisture from the air quickly, and wet nylon pops, strings and prints weak, so print it from a dry box. Most nylon filaments print at about 250 to 290 °C in an enclosure, and they warp, so use a brim and the bed surface the maker recommends.

Moisture changes printed nylon too. A part that has absorbed water gets more flexible but loses stiffness and strength, and one maker's datasheet lists wet tensile strength at less than half the dry figure. Its dimensions shift slightly as well, so allow for that in tight fits.

Carbon fiber nylon

Carbon fiber nylon (PA-CF) mixes short chopped fibers into nylon. Parts are much stiffer, warp less, hold dimensions better and have a matte surface that hides layer lines. The fibers are abrasive, so it needs a hardened steel nozzle. Use it for jigs, fixtures, drone frames and structural brackets.

Polycarbonate

Polycarbonate (PC) is very tough and holds its shape to around 110 °C. It needs a nozzle at about 250 to 285 °C, a bed at about 90 to 120 °C and an enclosure, and it warps readily. Use it when a part must survive heat and heavy impact together, such as a cover near a warm motor. For most other jobs, PETG or ASA is easier.

Powder-bed nylon: PA12 and PA11

SLS (selective laser sintering) and MJF (Multi Jet Fusion) printers fuse thin layers of nylon powder. The loose powder around the part supports it, so there are no support structures. PA12 is the most common powder. It makes strong, durable parts with similar strength in every direction, a slightly grainy surface and a natural gray or white color that is often dyed black. PA11 stretches further before it breaks, which suits snap fits and parts that take impacts.

These are professional machines, so powder-bed parts usually come from print services. They suit small production runs of functional parts, enclosures, clips and brackets where FDM layer lines or support scars are a problem. On Printlooper, production quotes cover SLS and MJF alongside FDM and resin.

Resins

Resin printers cure liquid photopolymer with UV light in layers of 0.025 to 0.05 mm, which gives detail and smooth surfaces that FDM cannot match at small sizes. Resin parts are usually more brittle and less heat resistant than filament parts, and uncured resin needs careful handling. Pick the resin type for the job.

Resin types and their uses
Resin typeWhat it is likeUse it for
StandardRigid and very detailed, brittle when thinDisplay miniatures, figurines and scale models
Tough or ABS-likeMore impact resistant, flexes slightly before breakingGaming miniatures that get handled, snap fits, functional prototypes
Flexible or elasticRubbery, rated on the Shore A scaleSmall gaskets, grips and soft-touch parts
Water-washableWashes in water instead of IPA, some are more brittleHobby prints where handling IPA is a problem
CastableBurns out cleanly with little ashJewelry and small metal parts made by investment casting

Water-washable resin is not safer to handle than other resins. Its wash water carries uncured resin and needs the same waste handling as used IPA, which how to 3D print explains. Castable resin needs the burnout schedule from the resin maker, since the wrong schedule leaves residue in the mold.

For buyers, resin is the choice for miniatures, jewelry and small detailed parts. Expect fine detail and smooth surfaces, but protect thin resin parts from drops, and keep standard resin out of strong sun, where it keeps curing, yellows and turns brittle. See the resin material page.

Colors, finishes and effects

Color and finish sell a product as much as shape does, and they change how a part prints.

  • Color varies by brand and batch. Two red PLAs from different makers rarely match, and one color can drift between production lots. Standardize on one brand per product and keep a reference print.
  • Dark glossy colors show every flaw. Black and dark glossy filaments show layer lines and blemishes most, while lighter and matte colors hide them.
  • Translucent filaments show the infill through thin walls. Add walls, or make the infill pattern part of the design, as many lamps do.

Finishes

  • Matte scatters light, hides layer lines and fingerprints, and looks closer to molded plastic.
  • Glossy looks rich in solid colors but shows every layer line and seam.
  • Smooth means fewer visible layer lines, from finer layers, resin or surface work such as sanding.
  • Textured surfaces break up reflections and hide layer lines and handling marks.
  • Silk has a metallic sheen that shifts with the light. It suits decor, with weaker layer bonding than standard PLA.

Effects

  • Solid is one color throughout, the predictable choice for products sold in numbers.
  • Gradient filament changes color along the spool, so the color shifts with height. No two prints match exactly, so say so in the listing.
  • Dual color filament carries two colors side by side in one strand, so a part shows different colors from different angles.
  • Glow filament charges in light and glows in the dark. Many glow blends are abrasive, so print them with a hardened nozzle.
  • Sparkle filament holds glitter-like flakes that catch the light and hide layer lines well.

Ordering by material, finish and effect

When you order a print, you pick the material family, color and finish, and choosing a material filters the results to print shops that stock it. Sellers have one more reason to favor common colors. If the shop a seller chose declines an order or is at capacity, the order is rerouted to another shop that stocks the same material and colors, and widely stocked colors give that reroute more options. Each family has its own page: PLA, PETG, ABS, TPU and resin.

Moisture, drying and storage

Most filaments absorb water from the air. Hygroscopic materials such as nylon, TPU and PETG absorb it fastest, nylon most of all. In the nozzle that water turns to steam, which causes popping, stringing, bubbles, rough surfaces and weak layer bonds.

Typical drying settings from filament makers' guides. The figure for your exact filament comes first.
MaterialMoisture sensitivityTypical dryingSigns it is wet
PLALow to moderate45 to 55 °C for about 6 hoursBrittle strands that snap, light stringing, faint popping
PETGModerate55 to 65 °C for about 6 hoursHeavy stringing, popping, rough or hazy surface
ABSLow to moderateAbout 70 °C for about 6 hoursPopping, rough surface, weaker layers
ASALow to moderate70 to 80 °C for 4 to 7 hoursPopping, rough surface
TPUHigh60 to 70 °C for 4 to 8 hoursBubbles, stringing, foamy texture
Nylon and carbon fiber nylonVery highAbout 90 to 100 °C for 6 to 8 hours, only in a dryer rated for itLoud popping, visible steam, rough and weak parts
PolycarbonateHigh75 to 85 °C for 5 to 6 hoursBubbles, popping, weak layers
ResinNot driedStore sealed, dark and within the maker's temperature rangeThick or separated resin, failed prints after long storage
  • Store open spools in sealed bins or bags with silica gel desiccant and a cheap hygrometer to show the humidity inside. Recharge the desiccant when it changes color.
  • Keep nylon dry, below about 20% relative humidity in one maker's guidance, and print nylon and TPU straight from a dry box.
  • Use a filament dryer, or a dehydrator kept for filament only. Never dry filament in a kitchen oven used for food. Home ovens also swing too far at low settings and can damage filament.
  • Never go above the maker's drying temperature, or the filament softens and sticks together on the spool. Check the spool's own limit too, since some plastic and cardboard spools deform first.
  • Keep resin bottles closed, out of sunlight and within the maker's storage range (Formlabs gives 10 to 25 °C for its resins), and shake or stir before each print because pigments settle.

Safety: food contact, resin, fumes and toys

Food contact

Food safe is a common question and a hard one to answer, for five reasons.

  • Layer lines form tiny grooves that trap food and bacteria, and normal washing does not clean them out.
  • Heat from dishwashers and hot water softens PLA and PETG, which can warp parts and open those grooves further.
  • Additives and colorants are often not approved for food contact, even when the base plastic is, and an approval covers the whole compound.
  • Nozzles are usually brass, and some brass nozzles contain lead, which is why food-contact guides call for a dedicated stainless steel nozzle.
  • Coatings sold as food safe only stay that way when applied, cured and maintained exactly as directed, and they wear and scratch with use.

Resin handling

Uncured resin irritates skin and eyes, and repeated contact can cause an allergy that gets worse with every exposure. Read the resin's safety data sheet (SDS), wear nitrile gloves (not latex) and safety glasses, work in a ventilated room away from living and sleeping areas, and keep resin away from children and pets. Wash and fully cure parts before anyone handles them bare-handed. Wet sand cured resin, or wear a dust mask when dry sanding. How to 3D print covers washing and waste.

Fumes and particles

Heated filament releases ultrafine particles and volatile organic compounds. NIOSH, the US occupational safety institute, reports that the amount depends on the material, color and nozzle temperature, and that ABS released more ultrafine particles than PLA in its studies. Ventilate the room for every material. Print ABS, ASA, nylon and polycarbonate in an enclosure with a filter or with venting to the outside, and never in a bedroom. ABS and ASA also give off styrene. Resin printers release particles and vapors too, so ventilate for them as well.

Toys and small parts

Small printed parts are a choking hazard for young children. Loose magnets are worse: the CPSC warns that swallowed magnets can attract each other through the intestinal walls and cause serious injury. Keep magnets fully enclosed so they cannot come loose, and keep magnet products away from young children.

In the US, toys and other products made mainly for children 12 and under must be third-party tested by a CPSC-accepted lab and certified in a Children's Product Certificate, toys for children under 3 must not contain small parts, and toys with magnets have their own requirements. Those are only some of the rules. Read the CPSC's toy safety guidance before you sell anything made for kids, and skip pet chew toys entirely.

Common products and the material that suits each

These are sensible defaults. The right answer still depends on where the product ends up and how people use it.

Common 3D printed products and the material to use
ProductMaterialWhy
Phone standsPLA, or PETG for a sunny deskRigid and low cost in any color. PETG adds heat headroom. Mounts for a car need ASA or ABS.
PlantersPETG, or ASA in full sunWater and soil are fine for PETG. Use 3 or more walls so the pot holds water.
Desk toysPLA, often silk, sparkle or gradientBright finishes at low cost, and print-in-place joints print cleanly.
D&D miniaturesStandard or tough resinFine layers capture faces. Tough resin survives drops.
KeycapsResin, or PETG for daily wearStems need accurate dimensions to fit switches. PETG resists wear.
Cosplay helmetsPLA or PLA+Light, low warping, easy to sand, prime and paint. Keep it out of hot cars, and sell it as a costume prop, never as head protection.
RC partsPETG or nylon, TPU for tiresImpact, flex and wear resistance. Nylon suits gears and arms.
Car mounts and dashboard partsASA or ABSSunlit dashboards get hotter than PLA's softening point and close to PETG's. Test the part in a real car.
Outdoor signs and garden partsASAResists UV and keeps its color and toughness in sun.
Gaskets, feet, bumpers and strapsTPU 95AGrips, seals and absorbs shocks without cracking.
Gears, hinges and clipsNylon or carbon fiber nylonLow friction and tough, flexes without snapping.
Enclosures for low-voltage electronicsPETG, ASA or ABSHandles warm components. Heat-set inserts give durable screw threads. Leave anything on mains power to certified parts and a qualified electrician.
Lamp shades for LED bulbsWhite or translucent PETG, kept clear of the bulbLED bulbs run much cooler than incandescent or halogen bulbs but still get warm. Sell the shade for use with certified lamp fittings, never with incandescent or halogen bulbs.
JewelryCastable resin for metal casting, resin or PLA for costume piecesCastable resin burns out cleanly, and standard resin gives fine detail. Wash and fully cure resin pieces, and make no hypoallergenic claims.
Cookie cutters, cups and utensilsSell as decorative, or skipLayer lines trap food and bacteria, and food safe claims are hard to back up.

Choosing what to make in the first place? Read 3D printed products that sell, and match the process to the design with FDM vs resin vs SLS.

Frequently asked questions

What is the best 3D printing material for beginners?

PLA. It prints at low temperatures, barely warps, needs no enclosure, smells mild and comes in the widest range of colors. Start with a standard PLA from a well-known maker and your printer's stock profile. Move to PETG when you need tougher parts or more heat resistance, and leave ABS, ASA, nylon and polycarbonate until you have an enclosure and some tuning experience.

What is the strongest 3D printing filament?

It depends on what strong means for the part. Polycarbonate and carbon fiber nylon are among the strongest and stiffest filaments most printers can handle, and nylon is among the toughest, bending rather than breaking. For everyday functional parts, PETG and ABS are strong enough and much easier to print. Wall count and orientation often matter as much as the material, since FDM parts are weakest between layers.

Is PETG better than PLA?

For functional parts, usually yes. PETG is tougher and less brittle, holds its shape to around 65 to 80 °C instead of about 55 to 60 °C, and copes better with moisture and sun. PLA is easier to print, stiffer, shows finer detail and comes in more colors and finishes. Choose PLA for display pieces and indoor decor, and PETG for parts that get handled, loaded or warm.

What is the best filament for outdoor use?

ASA. It resists UV, keeps its color and toughness in sunlight and holds its shape to around 90 to 100 °C. Like ABS, it needs an enclosed printer and ventilation. PETG works for light-duty outdoor parts and partial shade but ages faster in strong sun. Avoid PLA outdoors, since it softens in direct sun and fades, and avoid standard resin, which turns brittle.

Is 3D printed PLA food safe?

Not in any way you can easily promise. Even when the PLA itself is approved for food contact, layer lines trap food and bacteria, dishwasher heat softens PLA, colorants and additives are often not approved for food contact, and some brass nozzles contain lead. Do not sell printed items as food safe. Sell kitchen-themed products as decorative, or leave them out of your range.

Will PLA melt in a hot car?

It will not melt, but it can soften and sag. PLA starts to soften around 55 to 60 °C, and in an Arizona State University study, dashboards of cars parked in summer sun averaged about 69 °C (157 °F) after one hour. Phone mounts, vent clips and dashboard parts should be ASA, ABS or polycarbonate. PETG lasts longer than PLA but can still deform on a dashboard.

What is the difference between PLA and PLA+?

PLA+ is a modified PLA, usually with impact modifiers that make it tougher and less brittle. There is no standard for the name, so each brand's PLA+ is different. Some are much tougher than standard PLA, others differ very little, and heat resistance stays about the same. Check the maker's datasheet and test a sample before relying on it for functional parts.

Is resin stronger than filament?

Standard resin is usually more brittle than PLA or PETG, and most resins handle less heat than engineering filaments, with published heat deflection figures often between about 45 and 75 °C. Tough or ABS-like resins close much of the toughness gap for small parts. Resin's advantage is detail and smooth surfaces, not strength. For parts that take loads or impacts, PETG, nylon or ABS filament, or SLS nylon, is usually the better choice.

Further reading

Sources

Get it printed in the right material

Upload an STL or 3MF, choose a material family, color and finish, and compare all-in prices from print shops that stock it.

Compare print prices