How to get something 3D printed, from file to finished part
Everything you need to order a 3D print online: getting or preparing a file, choosing a process and material, what drives the price, one-off versus production runs, comparing quotes and checking the part when it arrives.
By Printlooper Team · Published · 20 min read
Key takeaways
- You need a printable 3D file, usually an STL or 3MF in millimeters. Without one, commission a designer, generate a prototype model, or download a model whose license allows your use.
- Match the process and material to the job: PLA for indoor decor and prototypes, PETG or ASA for tougher and outdoor parts, TPU for flexible parts, resin for fine detail and nylon for durable functional parts.
- Price follows material volume, material type, print time and height, supports, finish, quantity and shipping, so a smaller, lighter or better-oriented part usually costs less.
- Compare all-in prices rather than unit prices, and do not assume a turnaround: each print shop sets its own production time.
- Order one part before a batch. For larger runs, a production brief gets firm per-unit prices and lead times from several shops at once.
- When the part arrives, check it against the file and the order. Layer lines are normal on FDM prints, and typical tolerances are a fraction of a millimeter, not zero.
You do not need to own a 3D printer to get something printed. You need a 3D model file, a few decisions about material, color and finish, and a print service or print shop to make it. This guide walks through each step, whether you want one replacement part, a gift, a prototype or a batch of products to sell.
It is for buyers ordering a part for the first time, sellers getting a sample or a stock run made, and designers who want a physical proof of a model. You will learn what file you need and how to check it, how to choose a process and material, what makes a print cost more or less, when to switch from a one-off order to a production quote, how to compare quotes and what to check when the box arrives.
Printlooper is one place to order, and it appears where it is useful, but the steps apply to any print service.
What you need before you order
Every print starts with a 3D model file. A photo, sketch or list of measurements is not enough on its own, because a print shop needs geometry its slicer (the software that turns a model into printer instructions) can read. If you already have a file, skip to the next section. If not, pick the route that fits.
| Your situation | Route | What to know |
|---|---|---|
| You need a custom part or product | Commission a designer. On Printlooper you can post a brief, designers can reply with scope and price, and you pick one | Give measurements, photos and what the part has to do. Agree in writing who owns the result and what you can do with it |
| You want a quick prototype or a decorative idea | Describe it to the AI 3D model generator and get a printable model | Treat the result as a prototype. A print can differ from the preview, and it is not a route to parts that must fit something exactly |
| Something similar already exists | Download a model from a model library | Read the license first. Free to download does not mean free to print and sell |
| A broken part needs replacing | Measure it with calipers and have it modeled, or check whether the maker publishes a file | Note the original material and any load it carries. A printed copy is not always as strong as a molded original |
Downloaded models and licenses
A model you find online is still someone's work. In the US, the Copyright Office explains that a work is protected by copyright the moment it is created and fixed in a tangible form, and that registration is generally voluntary. So the license the creator chose is what tells you what you can do with a model. Many free models use Creative Commons licenses, which combine a few elements:
- BY (Attribution): you must credit the creator. On its own it allows sharing and adapting, including commercially.
- NC (NonCommercial): use must not be primarily intended for commercial advantage or monetary compensation. An NC model is not one to print and sell.
- ND (NoDerivatives): you can share the model unchanged, but not distribute adapted versions.
- SA (ShareAlike): adaptations must be shared under the same license terms.
Other sites use their own licenses, and some creators sell commercial licenses separately. In cases of doubt, the Copyright Office recommends getting permission, and you can ask the owner directly. That matters most for anything you plan to sell, and Selling 3D prints legally covers it in more depth.
Prepare the file: format, units, mesh and scale
Most failed orders start as file problems: a model in the wrong units, a mesh with holes, or walls too thin for any printer. Five minutes of checking before you upload saves a reprint.
| Question | STL | 3MF |
|---|---|---|
| What it holds | The triangle surface of a single object | Meshes plus units, colors, materials and several objects in one archive |
| Units | None stored. Software assumes a unit, almost always millimeters | Units defined in the file |
| Color | No standard way to store color | Colors and materials per object or per triangle |
| Standard | A long-established format that nearly every slicer reads | Published by the 3MF Consortium, and an ISO/IEC standard since 2025 |
| Best for | Single-color, single-part models | Multi-part and multi-color models, and anything where scale must be unambiguous |
Units and scale
Because an STL carries no units, a model drawn in inches or centimeters arrives at the wrong size: 25.4 times too small for inches, 10 times too small for centimeters. Export in millimeters, or export a 3MF, which records its units. After uploading, read the dimensions the viewer shows and compare them with a ruler, the part you are replacing or your sketch. Scale up or down in the CAD file, not by eye.
Mesh checks
A printable mesh is watertight (no holes in the surface) and manifold (every edge shared by exactly two faces), with outward-facing normals and no stray internal surfaces. Open the file in a free slicer such as PrusaSlicer, OrcaSlicer or Cura, which flags errors on import, or in a repair tool such as Blender's 3D Print Toolbox. Fix problems in the source model where you can, since automatic repairs can close a hole in the wrong place.
Before you upload
- The file is an STL or 3MF and opens in a slicer or viewer without errors.
- Overall dimensions match the real object or your sketch, in millimeters.
- The mesh is watertight and manifold, with no holes, flipped faces or loose internal shells.
- Each printed part is one solid body, and a multi-part model is exported as separate parts.
- Walls and details are thick enough for the process. On FDM, about 1.2 mm is a practical minimum for parts people handle.
- Anything that must fit another part has clearance designed in, and you know which faces matter.
- The file is under the service's size limit. Simplify an oversized mesh instead of cutting it up.
On Printlooper's print page, you can upload an STL or 3MF of up to 50 MB with up to 12 parts and preview it in the browser before you choose anything. A file is refused if no print shop's printer bed can hold it, so split oversized models into keyed parts first. Design for 3D printing covers wall thickness, clearances and splitting in detail.
Choose the process and material for the job
Three processes cover most orders. FDM (fused deposition modeling) melts plastic filament through a nozzle, layer by layer, and suits most everyday parts. Resin printing (SLA, DLP and similar) cures liquid resin with light in much thinner layers, for fine detail. Powder bed nylon (SLS or MJF) fuses nylon powder and needs no supports, which suits tough, complex functional parts. FDM vs resin vs SLS compares them in depth.
| The part is | Good starting choice | Why |
|---|---|---|
| Decorative, a gift or an indoor prototype | PLA (FDM) | Easy to print in many colors and finishes. Softens around 55 to 60°C, so keep it out of hot cars and strong sun |
| Functional indoors: brackets, holders, clips | PETG (FDM) | Tougher and more flexible than PLA, so it is less likely to snap |
| Outdoors: planters, signs, garden parts | ASA, or PETG for lighter duty | ASA has high UV and temperature resistance, so it is the usual pick for full sun. Prusa rates PETG for most outdoor use below 80°C |
| Near heat, such as motors or electronics | ABS or ASA (FDM) | Higher heat resistance than PLA. Check the grade's datasheet against your temperatures |
| Flexible: cases, bumpers, gaskets, straps | TPU (FDM) | Rubbery and impact absorbing. Hardness varies by grade |
| Small and detailed: miniatures, figures, jewelry models | Resin | Very fine layers and crisp detail. Standard resins are more brittle than filament plastics |
| Durable and complex: enclosures, snap fits, moving assemblies | Nylon (SLS, MJF or filament) | Tough and wear resistant, and powder processes print complex shapes without supports |
Material pages for PLA, PETG, ABS, TPU and resin have more detail, and 3D printing materials compares them side by side. On Printlooper's print page, material families are PLA, PETG, ABS, ASA, TPU, resin and nylon, and choosing one filters the list to print shops that stock it.
Color, finish and print strength
After the material, a few more choices shape how the part looks and behaves. Make them with the part's use in mind, not the preview alone.
Color
Filament colors vary between brands and batches, and screen previews are approximate. If an exact color matters, such as a brand color or a part that must match another, order one part first or plan to paint it. Translucent and silk colors look different depending on wall thickness and light.
Finish and filament effects
Finish describes the surface look. On Printlooper's print page, finishes include matte, glossy, smooth, textured and silk, and filament effects include solid, gradient, dual color, glow and sparkle. Matte and textured surfaces hide layer lines better than glossy ones. If you plan to sand and paint the part yourself, a plain solid color is enough, and How to finish 3D prints covers the rest.
Print strength
On FDM, strength depends on the number of walls, the infill (the internal pattern inside the part) and the print orientation, not just the material. Services package these settings in different ways. Printlooper offers three print strength choices, display, functional and solid. Choose by how the part will be used, and if it carries any load, order one and test it before you order more.
Hardware
Some parts need magnets, screws, threaded inserts or lighting. On Printlooper, hardware such as magnets, screws, LED kits and wiring can be added where your shop stocks it. Otherwise, buy the hardware separately and check its sizes against the pockets and holes in the model before you order.
How much does 3D printing cost? What drives the price
There is no single price per print, because every quote is built from the same handful of factors. Knowing them helps you read a quote and change the design or the order to bring the price down. Each print shop sets its own pricing. On Printlooper, shops typically price by the gram, and some add a minimum job price, a setup fee or a post-processing fee.
| Factor | Why it adds cost | How to bring it down |
|---|---|---|
| Material volume | More plastic or resin, and more time to lay it down | Scale down where size does not matter, hollow decorative parts, and keep walls only as thick as the job needs |
| Material type | Engineering plastics, nylon and resins cost more than PLA, and not every shop carries them | Use the least demanding material that does the job |
| Print time and height | Printer time is a cost of its own. Tall FDM parts need more layers, and on MSLA and DLP resin printers time follows height | Orient or split tall parts, and accept coarser layers on parts nobody inspects closely |
| Supports | Extra material, extra print time and labor to remove them | Design out steep overhangs so fewer supports are needed |
| Finish and effects | Specialty filaments and hand finishing add material cost and labor | Choose a standard finish unless the look matters for the product |
| Quantity | Setup costs spread across more units as quantity rises | Batch orders. On Printlooper, volume pricing starts at 25 units |
| Shipping | Size, weight and protective packaging for fragile parts | Combine parts in one order and keep parts compact enough for a smaller box |
A worked example
Say a desk organizer uses 120 g of PLA and a shop charges a hypothetical $0.10 per gram plus a $3 setup fee. One unit costs $15 before shipping. Thinner walls bring it to 90 g and $12. If the setup fee applies once per order, ordering 10 of the lighter version cuts its share to $0.30 per unit, so each unit costs $9.30. These numbers are made up to show the arithmetic, not real prices. Upload your own file to see actual quotes, and if you are pricing a product to sell, How to price a 3D printed product adds the other costs.
One-off, batch or production run
How many parts you need changes how you should order. A single part is a quick instant quote. A run of hundreds is closer to a manufacturing job, where a firm price, a lead time and consistency across units matter more than speed of ordering.
| Run size | Typical route | What to watch |
|---|---|---|
| One part or a prototype | Upload the file and compare instant prices | Treat it as a test. Check fit, finish and color before ordering more |
| A small batch | The same instant order at a higher quantity | Ask for the same material, color and settings across every unit, and check the first few closely |
| A production run with a deadline | Send one brief to several shops and compare firm per-unit prices and lead times | Give the need-by date, process and material up front, and ask about a pre-production sample |
Whatever the run size, order one part first. A sample costs a little time and money and catches what a preview never shows: a fit that is 0.2 mm tight, a color that reads differently in daylight, layer lines on the face that matters most.
How to compare 3D printing quotes
Two quotes for the same file can be far apart, because shops price, stock materials and schedule work differently. Compare them on the same basis, and remember the cheapest quote is only cheap if the part is right the first time.
What to compare on each quote
- The all-in price for the quantity you need: parts, any finish or hardware, and shipping.
- The exact material and color the shop stocks, not a near match.
- The process and layer height where the quote states them, since a cheaper quote can mean coarser layers.
- The production time. Each shop sets its own, so read it on each quote instead of assuming.
- Whether the price is per unit or per order, and how it changes at higher quantities.
- For production runs, whether the per-unit price is firm and whether a sample is included.
- The service's refund and shipping policies, including whether they cover a wrong size or an error in a file you supplied, and how you raise a problem.
On Printlooper's print page you compare all-in prices from approved print shops. There is no fixed lead time: each shop sets its own production time, so if you need parts by a date, put that need-by date in a production brief, compare the lead times shops reply with, and allow for shipping on top.
Ordering a 3D print online, step by step
The flow is much the same on most online print services. Here it is in order, with the checks that catch most mistakes.
- Upload the file Upload your STL or 3MF. A good service shows a 3D preview and the model's dimensions. Check them before anything else.
- Check the preview Spin the model. Look for missing faces, parts in the wrong place and a size that is off by 10 or 25.4 times, the signs of a unit mix-up.
- Set the quantity Order one for a first test, or the batch size you need once the sample has passed.
- Choose material, color and finish Pick the material for how the part will be used, then the color, finish and any filament effect.
- Choose strength and hardware Pick the print strength that matches the use, and add any hardware the part needs where the shop offers it.
- Compare and choose a shop Compare all-in prices and what each shop offers for your material and finish, then choose.
- Check the address and pay Check the delivery address and the total before you pay. On Printlooper, orders ship to US addresses only.
- Save the confirmation Keep the order details so you can match the parts against them on arrival and reorder the same combination later.
On Printlooper, all of this happens on the print page without an account, and payment is on one page. Independent print shops print and ship each order.
What to check when your print arrives
Open the box soon after delivery and check the parts against your file and your order while any problem is fresh. Photograph anything wrong, including the packaging, before you handle the part further.
On arrival
- The right number of parts, in the material, color and finish you ordered.
- No breaks, cracks or crushed areas from shipping.
- Overall dimensions match the file within the normal tolerance for the process.
- Holes, slots and mating faces fit their partner part or hardware.
- Supports are removed, leaving only small marks where they touched.
- No gaps between layers, layers that peel apart, warped corners or missing sections.
- Resin parts are hard and dry, not tacky, with no strong resin smell.
- Any hardware you ordered is present and seated.
What is normal
Layer lines are normal on FDM prints. They are how the process builds a part, and they show most on curved and gently sloped faces. Small marks where supports touched, a faint seam running up one side and slight color differences between filament batches are normal too. Gaps between layers, stringy webs, blobs, warped corners and tacky resin are not.
| Process | Typical tolerance | On a 100 mm part |
|---|---|---|
| FDM (filament) | Plus or minus 0.5%, with a lower limit of plus or minus 0.5 mm | About plus or minus 0.5 mm |
| Resin (SLA or DLP) | Plus or minus 0.15% to 0.3% depending on feature size, with a lower limit of plus or minus 0.02 mm | About plus or minus 0.3 mm |
| Powder nylon (SLS or MJF) | Plus or minus 0.5% or 0.3 mm, whichever is larger | About plus or minus 0.5 mm |
Tolerance is not the same as a printer's resolution. Formlabs points out that layer height and XY resolution do not describe the final dimensional accuracy of a part. If a fit is critical, design clearance into the model and order a test part before the batch.
If something is wrong
Contact the seller or service with your order number, photos and a short description of what does not match the order. Each service sets out what happens next in its own policies. On Printlooper, the refund policy and shipping policy explain how problems with an order are handled.
Your responsibility for the file and the part
When you upload a file to be printed, you are telling the service you have the right to have it made. On Printlooper, a buyer who uploads a file to the print page warrants in the Terms that they own it or are licensed to use it, and that making it does not infringe anyone's rights or break the law. That covers models you designed, models you commissioned with the right to print them, and downloads whose license allows your use. It does not automatically cover copies or scans of someone else's product, logos and characters you have no permission to use, or files shared without the creator's consent.
How the part is used is your responsibility too. Unless a service says otherwise in writing, assume nobody has tested whether your design suits your use. The same Terms say Printlooper does not design, manufacture, inspect or guarantee the accuracy, safety, quality, legality or fitness for any purpose of any file, design, quote or product. If a part matters for safety or carries a load, arranging that testing is up to you. Do not order weapons, weapon parts or anything made to get around a safety or security device.
On Printlooper, the print shop that makes an order receives the file to print it, and Printlooper does not use uploaded files to train AI models. If a design is confidential, read a service's terms before you upload. If you find your own design printed or sold without permission on Printlooper, the DMCA page explains how to send a notice.
Frequently asked questions
How do I get something 3D printed without a printer?
Upload a 3D model file, usually an STL or 3MF, to an online print service, choose the material, color and finish, compare prices and pay. A print shop makes and ships the part. On Printlooper you can do this on the print page without an account, with files up to 50 MB and up to 12 parts, shipping to US addresses. If you have no file, commission a designer or generate a prototype model first.
How much does it cost to 3D print something?
It depends on material volume, material type, print time and height, supports, finish, quantity and shipping. A small PLA part costs far less than a tall resin piece or a large nylon assembly. The quickest way to know is to upload the file and compare quotes. To lower the price, scale down where size does not matter, reduce supports, choose a standard finish and order more units at once.
Can I get my STL file printed?
Yes. STL is the most widely accepted format for 3D printing. Before you upload, check that it was exported in millimeters, that the overall size is right and that the mesh is watertight and manifold, with no holes or flipped faces. If the model has several parts or colors, a 3MF file keeps them together with their units. Make sure you own the file or its license allows your use.
What file format do I need for 3D printing?
STL and 3MF are the standard formats. STL stores only the surface of a single object, with no units or standard color. 3MF stores units, colors, materials and several objects in one file, and became an ISO/IEC international standard in 2025. Many services accept only these mesh formats, so photos, drawings and CAD files such as STEP need converting or modeling first.
How long does it take to get something 3D printed?
It depends on print time, the shop's queue and shipping. A small part can print in under an hour, while a large or detailed part can take a day or more on one printer. Each print shop sets its own production time, so do not assume a turnaround. For a deadline, request production quotes with a need-by date, and shops that quote reply with a lead time.
Can I print and sell a model I downloaded?
Only if its license allows it. In the US, copyright protects a work from the moment it is created and fixed in a tangible form, so the creator's license decides. Creative Commons licenses marked NC (NonCommercial) rule out use primarily intended for commercial advantage, and ND (NoDerivatives) rules out distributing adapted versions. Some creators sell commercial licenses separately. In cases of doubt, the U.S. Copyright Office recommends getting permission.
What is the difference between FDM and resin printing?
FDM melts plastic filament and builds the part layer by layer through a nozzle. It suits most everyday parts, offers many materials and colors and is usually the lower-cost option, but shows layer lines. Resin printing cures liquid resin with light in much thinner layers, giving fine detail and smooth surfaces for miniatures and figures, though standard resins are more brittle. Powder nylon (SLS or MJF) suits tough, complex parts.
Are layer lines on a 3D print a defect?
No. Layer lines are how FDM printing builds a part, and they show most on curved and gently sloped faces. Finer layers, a matte or textured finish or resin printing make them less visible, and sanding with filler primer removes them. Gaps between layers, layers that split apart, blobs and stringy webs are print defects worth raising with the seller or service.
Further reading
Sources
- 3MF Consortium: The 3MF file format
- Library of Congress: STL file format family
- Creative Commons: About CC licenses
- U.S. Copyright Office: Copyright in general FAQ
- U.S. Copyright Office: Fair use FAQ
- Formlabs: Guide to 3D printing tolerances, accuracy and precision
- Prusa Knowledge Base: PLA
- Prusa Knowledge Base: PETG
- Prusa Knowledge Base: ASA
- CPSC: Children's Product Certificate FAQ
Upload a file and compare prices
Upload an STL or 3MF of up to 50 MB, choose material, color, finish and strength, and compare all-in prices from approved print shops. No account needed.
Order a print